To display entries in the Ethernet ARP routing table, enter the show arp ethernet command in User Exec mode or Privileged Exec mode. show arp ethernet Syntax Description This command has no arguments or keywords. Defaults This command has no default settings. Command Modes User Execute...
Show Commands This chapter describes the Cisco NX-OS Multiprotocol Label Switching commands that begin with Show. show bgp unicast neighbors vrf To display information about Border Gateway Protocol (BGP) neighbors, use the show bgp unicast neighbors vrf command. show bgp {ipv4 | ipv6} uni...
CISCO的show命令和interface命令大全 ShowCDPlooksatswitchesandrouters TheshowCDPentry*isthesameastheshowcdpneighbordetail command,butnotforthe1900switch TheshowCDPinterfacedisplaysaspecificinterfacethat enablesCDP Showcdpneighbordisplaysdirectconnectedneighbordevices andtheirdetailedinformation Theshowcdpneighbordetaildisp...
S1#conf t S1(config)#interface vlan 1 S1(config-if)#no shutdown (this command will activate the interface) S1(config-if)#Ctrol+C (=2*exit) S1#show interface brief 2. Config Passwords 2.1. Secure User EXEC Mode Access. To secure user EXEC mode access, enter line console ...
Option 1: Command Selection 在Command Selection菜单中,选择在每个角色(APIC、Leaf、Spine)中所需要运行的命令和抓取日志的节点。 不同节点shell类型所支持的命令如下: APIC: moquery、show command、acidiag Leaf: ish、vsh、vsh_lc Spine(Box): ish、vsh、vsh_lc Spine(Chassis): ish、vsh、line...
setup Run theSETUPcommand facility show Show running system information ssh Open a secure shell client connection--More-- more表示由于屏幕大小原因,还有部分内容没有显示出来: 回车键:一次向下显示一行 空格键:一次向下显示一屏 特权用户模式转为全局配置模式: ...
class-map Show QoS Class Map clock Display the system clock cns CNS subsystem …… 显示出 show命令后面可以跟的各个参数,查看过程中按ESC中止显示,回车继 续显示,并可以立即输入需要的参数。如输入参数后,回车执行,屏幕提示% Incomplete command.,说明命令输入不完整,还需要参数,可以通过 ?继续查 ...
Show vlan only shows default vlan1 and the other vlans that come with the IOS example fddi token ring etc. but not the one I created. When I did a show vtp status I got this switch# show vtp statusVTP Version capable : 1 to 3VTP Version running : 1VTP Domain Name :VTP Pruning ...
Cisco的网m际操作系统(IOS:Internetwork Operating Syste),IOS配置通常是通过基于文本的命令行接口(Command Line Interface,CLI)进行的。 二、路由其基本操作 1、基本操作模式 1)用户模式 Router> #通常可以查看统计信息 Router>logout #退出用户模式 2)特权模式 ...
Pconline# show interface fastethernet 0/1 /*查询端口0/1的配置结果 配置交换机端口模式: 交换机的端口工作模式一般可以分为三种:Access,Multi,Trunk。trunk模式的端口用于交换机与交换机,交换机与路由器,大多用于级 联网络设备所以也叫干道模式。Access多用于接入层也叫接入模式。暂时我们先介绍Trunk模式和Access...