ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route, H - NHRP, l - LISP a - application route + - replicated route, % - next hop override Gateway of last resort is not set ...
* - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route, H - NHRP, l - LISP a - application route + - replicated route, % - next hop override, p - overrides from PfR Gateway of last resort is not set 10.0.0.0/8 is variably subnetted, 4...
switch(enable) set ip route default gateway 42. 为一个路由处理器分配VLANID,可在接口模式下使用下列命令: router(config)# interface interface number router(config-if)# mls rp vlan-id vlan-id-num 43. 在路由处理器启用MLSP: router(config)# mls rp ip 44. 为了把一个外置的路由处理器接口和交换...
GuanWei(config-route-map)#set ip default next-hopip-address[weight][ip-address[weight]] 为路由表中没有明确路由的数据分组指定下一跳IP地址 GuanWei(config-route-map)#set ip next-hop ip-address[weight][ip-address[weight]] 设置数据包的下一跳IP地址 GuanWei(config-route-map)#set interface int...
ip route0.0.0.00.0.0.0192.1.0.65 即只要没有在路由表里找到去特定目的地址的路径,则数据均被路由到地址为192.1.0.65的相邻路由器。 2第二章:广域网协议设置 一、HDLC HDLC是CISCO路由器使用的缺省协议,一台新路由器在未指定封装协议时默认使用HDLC封装。
ip default-gateway172.16.1.1为模拟PC的略由器配置一个默认网关 配置一条静态路由 Branch(config)#ip route 172.16.1.0 255.255.255.0 e0/1 192.168.1.1 //告诉路由器,去往172.16.1.0/24这个网络应该将数据从e0/1接口转发出去,交给192.168.1.1这个设备 ...
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, * - candidate default U - per-user static route, o - ODR Gateway of last resort is not set 1.0.0.0/24 is subnetted, 1 subnets C1.1.1.0 is directly connected, Loopback0 ...
R1(config-route-map)#set ip default next-hop 2.2.2.2 都多了一个default,区别是:不含default的命令,是不查询路由表就转发数据包到下一跳IP或接口(先策略后路由),而含有default的命令是先查询路由表,在找不到精确匹配的路由条目时,才转发数据包到default命令指定的下一跳IP或接口(先路由后策略)。
route-map PBR_WAN permit 10match ip address LIST_WANset interface GigabitEthernet0. 0 有帮助 回复 Translator Community Manager 发布时间 04-07-2022 09:09 PM Hello, 从debug输出判断,PBR似乎确实在工作。尝试并简化NAT,如下所示: --> ip nat inside source list 1 interface Cellular0 over...
Router(config)#ip route 0.0.0.0 0.0.0.0 30.0.0.1 The following image shows how to run this command in the packet tracer. How a default route and routing work When a router receives a packet on its interface, it reads the destination network address of the incoming packet and locates ...