导航到Feature templateCisco VPN> IPv4 Route > New IPv4 Route > Prefix。添加前缀0.0.0.0/0(或企业ID)。修改0.0.0.0/0 > Add a Next Hop的条目。在address字段下指定DHCP。 通过CLI配置 要更改默认DHCP管理距离,请在接口配置中使用ip dhcp client default-routerdistancecommand: cEdge#config-transaction cEd...
Router(config)# ip route <目录网络或子网号> [子网掩码] <下一路由器IP地址 | 从本地出口 的地址> [管理距离0~255,默认为1] (注:静态地址配置) *ip default-network命令 Router(config)# ip default-network <目标网络号> (注:配合路由协使用,用其中的一个动态路由号作默认路由配置) Router(config)#...
deleteDeletes a route changeModifies a current route destinationSpecifies the computer to send command mask subnetmaskSpecifies a subnet mask to be associated with this route entry (default subnet mask is 255.255.255.255) Thedestinationspecifies the network destination of the route. The destination c...
---System Configuration Dialog---At any point you may enter a question mark'?'forhelp.Use ctrl-c to abort configuration dialog at any prompt.Default settings areinsquare brackets'[]'. 这是告诉你在设置对话过程中的任何地方都可以键入“?”得到系统的帮助,按ctrl-c可以退出设置过程,缺省设置将显示...
Default settings are in square brackets '[]'. 这是告诉你在设置对话过程中的任何地方都可以键入“?”得到系统的帮助,按ctrl-c可以退出设置过程,缺省设置将显示在‘[]’中。然后路由器会问是否进入设置对话: Would you like to enter the initial configuration dialog? [yes]: ...
interface Async 1ip address 202.96.1.1 255.255.255.252encapsulation pppdialer in-banddialer idle-timeout 60dialer map ip 202.96.1.2 name router2 modem-script cisco-default 2113470dialer-group 1ppp authentication chap!router eigrp 200redistribute connectednetwork 202.96.0.0!ip route 202.96.37.0 255.255....
defaultSetacommandtoitsdefaults delaySpecifyinterfacethroughputdelay descriptionInterfacespecificdescription diffservdiffserv(Provisioning) dlswDLSwinterfacesubcommands dspuDownStreamPU duplexConfigureduplexoperation. exitExitfrominterfaceconfigurationmode fair-queueEnableFairQueuingonanInterface frasDLCSwitchInterfaceCommand
// 各个interface的信息, ip地址, 查看子网掩码等(以及vty, console的密码等) show running-config // 管道 show run | include mask show run | begin mask // 查看是否使能每个interfaces, no shutdown show ip interface brief show ipv6 interface brief // 查看route table, 显示自己的和外部的C和L,...
Default settings are in square brackets '[]'. 这是告诉你在设置对话过程中的任何地方都可以键入“?”得到系统的帮助,按ctrl-c可以退出设置过程,缺省设置将显示在‘[]’中。然后路由器会问是否进入设置对话: Would you like to enter the initial configuration dialog? [yes]: ...
IP route command ran succesfully Switch(config)#ip route 0.0.0.0 0.0.0.0 192.168.1.9 Switch(config)#end But when i tried to see the route, I didn't see it. I ran the commands you gave me in order to assign all interfaces to the VLAN. I didn't set "fastport" paramet...