遠端站點路由器的配置如下: interface Serial 0 ip address 10.1.2.2 255.255.255.0 ! interface Ethernet 0 ip address 10.1.1.1 255.255.255.0 ! ip route 0.0.0.0 0.0.0.0 10.1.2.1 ! no ip classless 透過此設定,遠端站點的主機可以到達網際網路(透過10.x.x.x雲端)上的目的地,但無法到達位於企業網路10....
interface Serial1/0 ip address 10.10.10.2 255.255.255.252 ! interface Serial2/0 ip address 10.10.20.2 255.255.255.252 ! ip route 0.0.0.0 0.0.0.0 10.10.10.1 ip route 0.0.0.0 0.0.0.0 10.10.20.1 250 ! 以下是 R1 的路由表: R1#show ip route Codes: L - local, C - connected, S - static...
"Note:This step can be omitted if the switch reaches the default router through a VLAN. In its place, configure an IP address for that VLAN interface." The statement of "...default router through a VLAN." is ture in my case. Which brings me to my question: Can some please give me ...
Router(config)#int fa0/0 Router(config-if)# ip address 192.168.1.1 255.255.255.0 設定FastEthernet 0/1 為 10.10.1.1/24 Router(config)# int fa 0/1 Router(config-if)# ip address 192.168.1.1 255.255.255.0 查詢FastEthernet 0/0 0/1 IP相關資訊 回到特權模式 Router# show interface FastEthernet...
interface: dmz_ftp source: 10.50.5.3 translated (interface): outside translated (Use IP address): 12.175.10.206 Port Address Translation (PAT): ENABLE (checkbox) PAT (protocol): TCP PAT (orginal port): ftp (port 21) PAT (translated port): ftp (port 21) ...
no ip address ! interface Management0/0 shutdown管理接口, nameif management通常情況我是將他SHUTDOWN的 security-level 100 ip address 192.168.1.1 255.255.255.0 management-only ! passwd 2KFQnbNIdI.2KYOU encrypted設置telnet密碼 boot system disk0:/asa722-k8.bin設置開機引導的IOS文件 不知道用什麽文件引...
[r2-GigabitEthernet0/0/0]ip address 20.1.1.1 24 <r3>system-view [r3]interface GigabitEthernet 0/0/1 [r3-GigabitEthernet0/0/1]ip address 20.1.1.2 24 2.R1上配置去往20网段的静态路由 [R1]ip route-static 20.1.1.0 24 g0/0/0 10.1.1.2 ...
IP address: 140.112.2.1 Platform: cisco 3640, Capabilities: Router Interface: FastEthernet10/1, Port ID (outgoing port): FastEthernet0/0 Holdtime : 142 sec --- Device ID: Switch Entry address(es): IP address: 140.112.8.10 Platform:
route-map PBR6 permit10match ip address101setip next-hop200.200.200.2route-map PBR6 permit20match ip address100setip next-hop100.100.100.2 3. 將route-map加至來源IP入口方向的介面上 interfaceEthernet0/0ip address1.1.1.1255.255.255.0ip policy route-map PBR6...
interface: outside Crypto map tag: VPN_crypto_map_name, seq num: 2, local addr: 172.25.50.101 access-list integ-ppe-loopback extended permit ip anyvpc_subnetsubnet_masklocal ident (addr/mask/prot/port): (0.0.0.0/0.0.0.0/0/0) remote ident (addr/mask/prot/port): (vpc_subnet/subnet_...