遠端站點路由器的配置如下: interface Serial 0 ip address 10.1.2.2 255.255.255.0 ! interface Ethernet 0 ip address 10.1.1.1 255.255.255.0 ! ip route 0.0.0.0 0.0.0.0 10.1.2.1 ! no ip classless 透過此設定,遠端站點的主機可以到達網際網路(透過10.x.x.x雲端)上的目的地,但無法到達位於企業網路10....
interface Serial1/0 ip address 10.10.10.2 255.255.255.252 ! interface Serial2/0 ip address 10.10.20.2 255.255.255.252 ! ip route 0.0.0.0 0.0.0.0 10.10.10.1 ip route 0.0.0.0 0.0.0.0 10.10.20.1 250 ! 以下是 R1 的路由表: R1#show ip route Codes: L - local, C - connected, S - static...
"show interface ip brief"コマンドで 各Interfaceの IPアドレスや、Down/Up状態を確認できます。 Internet-FW-01# show interface ip briefInterface IP-Address OK? Method Status ProtocolGigabitEthernet1/1 172.16.0.1 YES CONFIG up upGigabitEthernet1/2 unassigned YES unset d...
没有切换到Cisco ACS登录。请教了几位同事，说是可能因为 ip tacacs source-interface Lookback0这句，...
no ip address ! interface Management0/0 shutdown管理接口, nameif management通常情況我是將他SHUTDOWN的 security-level 100 ip address 192.168.1.1 255.255.255.0 management-only ! passwd 2KFQnbNIdI.2KYOU encrypted設置telnet密碼 boot system disk0:/asa722-k8.bin設置開機引導的IOS文件 不知道用什麽文件引...
百度试题 结果1 题目以下哪个命令用于配置Cisco设备上的接口? A. configure terminal B. interface C. ip address D. hostname 相关知识点: 试题来源: 解析 A 反馈 收藏
Router(config-if)# ip address 192.168.1.1 255.255.255.0 設定FastEthernet 0/1 為 10.10.1.1/24 Router(config)# interface FastEthernet 0/1 Router(config-if)# ip address 192.168.1.1 255.255.255.0 設定方式 2 : 可用簡寫 設定FastEthernet 0/0 為 192.168.1.1/24 ...
IP address: 140.112.2.1 Platform: cisco 3640, Capabilities: Router Interface: FastEthernet10/1, Port ID (outgoing port): FastEthernet0/0 Holdtime : 142 sec --- Device ID: Switch Entry address(es): IP address: 140.112.8.10 Platform:
route-map PBR6 permit10match ip address101setip next-hop200.200.200.2route-map PBR6 permit20match ip address100setip next-hop100.100.100.2 3. 將route-map加至來源IP入口方向的介面上 interfaceEthernet0/0ip address1.1.1.1255.255.255.0ip policy route-map PBR6...
interface vlan 1 ! nameif inside ! security-level 100 ! ip address <PrivateIPAddress> <Netmask> ! exit ! ! interface vlan 2 ! nameif outside ! security-level 0 ! ip address <OnPrem_Device_Public_IP> <Netmask> ! exit ! ! route outside 0.0.0.0 0.0.0.0 <NextHop IP> 1 ! ! =...