46 input errors, 0 CRC, 0 frame, 46 overrun, 0 ignored 0 watchdog, 16164 multicast, 0 pause input 78723290 packets output, 1917039290 bytes, 0 underruns 0 output errors, 0 collisions, 0 interface resets 870 unknown protocol drops 0 babbles, 0 late collision, 0 deferred 0 lost carrier, ...
Common Causes: This can occur in a high throughput situation where an interface is hit with a high volume of bursty traffic from many other interfaces all at once. Interface resets can occur along with the underruns. Undersize Description: CatOS sh port and Cisco IOS sh...
debug serial interface命令是直接与路由器接口和传输介质类型相关的调试命令。在下面的示例中,串行接口采用HDLC封装。端到端的HDLC保持活跃的报文每10秒钟交换一次。这表明链路操作正常并且第二层工作正常。show interface serial0命令表明线路协议正常启动。使用undebug all命令关闭所有的调试。 协议调试 下面我们举协议调...
show ip interface brief将显示每一个路由器接口的IP地址信息以及第二层的状态信息(如下所示)。其他与IP对应的协议的相关性信息可以通过相应命令属性获得,比如show ipx interface brief。 YH-Router#sh ip in brief Interface IP-Address OK? Method Status Protocol TokenRing0/0 172.26.12.3 YES NVRAM up up To...
因此,NP计数器中的L3_NOT_MYMAC意味着路由器在第3层接口上收到一个帧,其目的MAC地址不是该接口之一。路由器按预期丢弃它,这在show interface中报告为输入丢弃。 在ASR 9000上,对于ASR 9000的子接口上未配置dot1q VLAN接收的数据包,Input drop unknown 802.1Q计数器不会在show controllers gigabitEthernet 0/0...
在IP 环境中,ARP 类型是 ARPA。可以通过使用 arp interface 命令将封装改为 HP PROBE 或 SNAP。 ARP 协议设置了一个计时器,当计时器到期后会清除相关的 ARP 记录,这个计时器的时间 CISCO 默认是4小时(14400S),当然大家可以在接口下通过 arp timeout 命令进行修改。
In certain scenarios the local mGig port (an interface from the mGig linecard C9600-LC-48TX) can also experience the same type of loss in the form of input errors (CRC, FCS) on the interface. As shown in the table, the structure of an Ethernet packet, which inclu...
14、show interface |ierrors|FastEthernet|GigabitEthernet:查看接口是否存在大量input或output errors包错误 15、show processes cpu:查看设备cpu负载 16、show processes mem:查看设备mem负载 17、show access-list:查看访问控制列表配置及匹配数据包数量 18、show logging:查看本机内部日志记录情况 ...
Interface is up;line protocol is up(looped) 链路在某处环路 Incrementing carrier transition counter 1) 来自本地提供商的信号不稳定2) 线缆故障3) 硬件故障 Incrementing interface resets 1) 线缆故障,导致CD信号丢失2) 硬件故障3) 线路拥塞 Input drops,errors,CRC,and framing errors 1) 线路速率超过接口...
只有2 input errors, 1 CRC, 1 frame,2 interface resets。按道理不足以导致接口进入err-disabled状态。 没有办法,只能配置err-disabled。启用recovery功能。命令如下: GX-SW-2950-01(config)#errdisable recovery interval 30 GX-SW-2950-01(config)#errdisable recovery cause all ...