You'll notice that the "input errors" count is exactly the same as the "drops" shown on the Input queue line. This means that the packet that caused the input error was dropped by the router as the input queue for the interface was already full. This problem can be caused by the fac...
Last clearingof "show interface" counters never 表示离上次执行“clear counters”命令之后经历了多少时间,“clear counters”命令可以把last input/output的“show interfaces” 计数器全部清零,这可以方便排错 13.队列策略 Queueing strategy:fifo 默认为先入后出 (First in first out, FIFO) 14.队列 Input queue...
1、通常我们使用show interface命令来查看接口的信息,如show interface gig 1/0或者show int pos 2/0等来分别查看路由器上千兆以太接口和POS接口的端口信息。 查看以太网接口信息,在7507上使用命令为: show interfacesfastethern et slot/port-adapter/port查看POS接口信息,在7507上使用命令为: show interfaces pos...
Lastclearing of "show interface" counters 0:56:40 表示离上次执行“clear counters”命令之后经历了多少时间,“clear counters”命令可以把除lastinput/output的“show interfaces”计数器全部清零,这可以方便排错 Queueing strategy: fifo 说明该接口采用默认传统的先入先出队列机制 Outputqueue 0/40, 0 drops;input...
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 4013 packets output, 1357412 bytes, 0 underruns 0 output errors, 0 applique, 0 interface resets 0 output buffer failures, 0 output buffers swapped out 0 carrier transitions 3、下表给出了show interface的输出中所有表项的具体含...
Show Interface命令输出信息量大,包含了该接口方方面面的统计信息,如下所示: Router#show interfaces fastethernet 3/0 FastEthernet3/0 is up, line protocol is up Hardware is TSWITCH, address is 00e0.f7a4.5130 (bia 00e0.f7a4.5130) MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, rely 255/255...
在IP环境中,ARP类型是ARPA。可以通过使用arp interface 命令将封装更改为HP PROBE或SNAP。 ARP超时的默认值为4个小时。 13.最后的输入输出 Last input 00:00:11, output 00:00:12, output hang never 表示最后一个被接口成功接收的数据包确切的时间。该显示用于指出该接口出现故障的具体时间。
通过show ip interface brief命令可以查看交换机的IP地址信息 查看交换机接口状态及描述 通过show int st命令可以查看交换机的接口是否UP 通过在特权模式上show interfaces description接口连接的描述信息 查看交换机接口报文统计 通过show int g0/x counters命令可以查看交换机的接口的收发包情况 ...
show interface status #查看交换机接口状态是否存在error disable接口disable接口 show interface summary #查看交换机所有接口当前接口流量 show interface |ierrors|FastEthernet|GigabitEthernet #查看接口是否存在大量input或output errors包错误 show processes cpu #查看设备cpu负载 ...
1、show interface 命令详解2011-03-04 06:27:41| 分类: cisco | 标签: |字号大中小 订阅 .Router#show interfaces e4/0Ethernet4/0 is up, line protocol is upHardware is Lance, address is 000b.bf30.f470 (bia 000b.bf30.f470)Internet address is 1.1.1.9/24MTU 1500 bytes, BW 10000 Kbit...