Command qualified for use in Cisco vManage CLI templates. Usage Guidelines Example Device(config)# sdwan Device(config-sdwan)# interface ge0/2.101 Device(config-interface-ge0/2.101)# access-list acl1 in allow-
'. If nothing matches the currently entered incomplete command, the help list is empty. This indicates that there is no command matching the input as it currently appears. If the request is within a command, press the Backspace key and erase the entered ...
ip nat pool c2501202.96.38.1202.96.38.62netmask255.255.255.192interfaceEthernet0ip address10.1.1.1255.255.255.0ip nat inside!interfaceSerial0ip address202.200.10.5255.255.255.252ip nat outside!ip route0.0.0.00.0.0.0Serial0access-list2permit10.0.0.00.0.0.255!DynamicNAT!ip nat inside source list2pool...
Interfacestate:InterfaceNext-HoporVCD,State/Mode (*,239.255.255.25402:34:52/00:02:20,RP0.0.0.0,flags:DJC Incominginterface:,RPFnbr0.0.0.0 Outgoinginterfacelist(就是OILIST) FastEthernet0.21,ForwardDense,02:34:52/00:00:00 (*,224.2.160.103),0d/00:02:59,RP0.0.0.0,flags:DJC Incominginterface...
[Switch-Vlan-interface3] quit # 将端口GE1/0/2加入到指定VLAN。 [Switch] interface GigabitEthernet 1/0/2 [Switch-GigabitEthernet1/0/2] port switchcess vlan 3 [Switch-GigabitEthernet1/0/2] quit # 开启全局802.1x认证。 [Switch] dot1x # 配置802.1x认证的认证方法为CHAP。 [Switch] dot1x ...
cdpCDPinterfacesubcommands cmnsOSICMNS custom-queue-listAssignacustomqueuelisttoaninterface defaultSetacommandtoitsdefaults delaySpecifyinterfacethroughputdelay descriptionInterfacespecificdescription diffservdiffserv(Provisioning) dlswDLSwinterfacesubcommands dspuDownStreamPU duplexConfigureduplexoperation. exitExitfrom...
switch(enable) set vlan vlan-num mod-num/port-list 9. 在基于IOS的交换机上配置VLAN中继线: switch(config)# interface interface mod/port switch(config-if)# switchport mode trunk switch(config-if)# switchport trunk encapsulation {isl|dotlq} ...
switch(enable)setvlanvlan-nummod-num/port-list 9.在基于IOS的交换机上配置VLAN中继线: switch(config)#interfaceinterfacemod/port switch(config-if)#switchportmodetrunk switch(config-if)#switchporttrunkencapsulation{isl|dotlq} switch(config-if)#switchporttrunkallowedvlanremovevlan-list ...
GNS3中,在路由启动之前,右击路由选择"Configure"->"Slots"可以给路由添加接口模块;设备启动后,双击图标即可打开CLI(Command Line Interface,命令行接口),或使用上一篇文章中介绍的PAC等终端连接管理器;如果想要显示接口编号在GNS3菜单中"View"->"Show/Hide interface labels"打钩; ...
zone-pair Zone pair command 区域对命令 接口配置模式下: arp Set arp type (arpa, probe, snap) or timeout 设置ARP型(ARPA,探针卡)或超时 bandwidth Set bandwidth informational parameter 设置带宽信息参数 cdp CDP interface subcommands CDP接口子命令 channel-group Add this interface to an Etherchannel ...