switch(config-if)#no shutdown ②、配置接口全双工 switch(config-if)#duplex full ；设置该端口为全双工 switch(config-if)#description up_to_mis ；设置该端口描述为 up_to_mis switch(config-if)#end ；退回到特权模式 ③、接口描述 switch(config)#interface fastethernet 0/1 switch(config)#description...
Router(config-if)#ip address 192.168.1.1 255.255.255.0输入接口IP地址和掩码 Router(config-if)#no shutdown路由器接口默认都为shutdown,所以要启用,就要打no shutdown 注意:默认情况下如果没有设置虚拟终端密码是无法从远端进行telnet的,远端进行telnet时候会提示设置login密码。许多新手会认为no login是无法从远端...
switch(config-if)#no shutdown ②、配置接口全双工 switch(config-if)#duplex full ;设置该端口为全双工 switch(config-if)#description up_to_mis ;设置该端口描述为 up_to_mis switch(config-if)#end ;退回到特权模式 ③、接口描述 switch(config)#interface fastethernet 0/1 switch(config)#description o...
Command History Release Modification 12.2(50)SG This command was introduced. Usage Guidelines Do not enter the show authentication sessions and the clear authentication sessions commands in succession and repeatedly - it causes the switch to shutdown. These commands must not be used t...
switch(config-if)#no shutdown ②、配置接口全双工 switch(config-if)#duplex full ;设置该端口为全双工 switch(config-if)#deion up_to_mis ;设置该端口描述为 up_to_mis switch(config-if)#end ;退回到特权模式 ③、接口描述 switch(config)#interface fastethernet 0/1 ...
!--- The interface is up (or not in a shutdown state), but line protocol down. !--- Reason: In this case, the device on the other side of the wire is a !--- CatOS switch with its port disabled. Router#show interfaces fastEthernet 6/1 statusPort Name Status Vlan Duplex Speed ...
switchname MDS9148-1 interface mgmt0 ip address 192.168.10.12 255.255.255.0 gatway 192.168.10.1 no shutdown ssh key rsa 1024 force feature ssh feature telnet feature http-server system default switchport shutdown system default switchport trunk mode off ...
The following configuration command s cript was created:hostname Router enable secret5$1$W5Oh$p6J7tIgRMBOIKVXVG53Uh1 enable password pass ……… 请注意在enable secret后面显示的是乱码,而enable password后面显示的是设置的内容。 显示结束后,系统会问是否使用这个设置: 代码...
, IOS puts the interface in an error disabled (err-disabled) state, which makes the switch stop all inbound and outbound frames. To recover from this state, someone must manually disable the interface with theshutdowninterface command and then enable the interface with theno shutdowncommand....
小编很懒,好久没更新文章了,今天抽风,汇总一下IDC中心不同厂家设备的端口光衰(光功率值)查看命令,当前数据机房所有设备都是光纤互联,所以查看设备之间两个端口光衰是尤为重要的。不同厂家设备的端口光功率值查看命令是不一样的,容易混淆和忘记,这里汇总一下,备忘。