1. 硬件连接 将Cisco 2960系列交换机连接到电源并启动。使用控制台电缆（RJ-45到RS-232）将PC连接到交换机的控制台端口。确保PC上安装了终端仿真软件，如PuTTY或Tera Term。2. 软件准备 下载并安装终端仿真软件。设置终端仿真软件的连接参数：波特率9600、数据位8、无奇偶校验、停止位1、无流控。3. 进入Cisco 296...
The documentation provided by Cisco states that the default password is simply cisco and that a username is unnecessary. Needless to say, it doesn't work. I've also Googled for other default passwords (such as cisco-cisco as the username-password), none of which worked either. I've ...
Table 11-1 shows the default password and privilege level configuration. Table 11-1 Default Password and Privilege Levels Feature Default Setting Enable password and privilege level No password is defined. The default is level 15 (privileged EXEC level). The password is n...
1、cisco交换机2960配置转载 分享该日志 评论 举报21 | 载阅厂(6) 评论:配置密码:2960>en ;第一次密码为空2960h#conf t ;进入全局配置模式2960(config)#hostname swa ;设置交换机名2960(config)#enable secret aaa ;设置特权加密 口令为 aaa2960(config)#enable password aax ;设置特权非密 口令为 aax...
john.pan.s Level 1 In response to chucktranhpb 08-04-2019 11:53 AM I just don't know why should use "aaa authentication enable default enable" if you are not using AAA. This happened to me today that even with local username and password defined and with login local command fo...
1、附录A:Cisco 2960S交换机配置操作规范1. 将交换机上电,约一分半钟进入工作模式,此时指示灯SYST和STAT是亮的,DUPLX,SPEED不亮。2. 按住交换机前面板的MODE按钮约3秒后,放开MODE按钮重新按住,直到所有灯转为琥珀色,松开按钮,此时交换机会自动清空配置,并自动重启。约一分半钟后重启完毕,进入工作模式,进行步骤...
附录A:Cisco2960S交换机配置操作规范将交换机上电,约一分半钟进入工作模式,此时指示灯SYST和STAT是亮的,DUPLX,SPEED不亮。按住交换机前面板的MO..
default-runm ng-config dr-x <no date> memory -r山 1934 <no date> 『unning-config dr-x vfi1 2413 Nospace information available switchil^copy flash:Acinf已xi*oldbsystem:/runnIng-config Desfinaticnfi1enane[runn-ng-conf1g]? 4785 bytas亡叩彳色din0.512 secs(站倨bytes/sec^ JF-48-02# ...
Cisco 2960S交换机配置操作规范 1.将交换机上电，约一分半钟进入工作模式，此时指示灯SYST和STAT是亮的，DUPLX，SPEED不亮。2.按住交换机前面板的MODE按钮约3秒后,放开MODE按钮重新按住，直到所有灯转为琥珀色，松开按钮，此时交换机会自动清空配置，并自动重启。约一分半钟后重启完毕，进入工作模式，进行步骤3操作...
.enable password line vty 0 15password 123no snmp-s erver!interface GigabitEthernet0/2!end6、组态信息显示完后,出现如下对话栏,输入2并回车保存 交换机配置信息。[0] Go to the IOS cojhand prompt without saving this conf ig.[1] Return back to the setup without saving this conf ...