I've also tried resetting the switch back to its factory default a few times. Any help with this would be greatly appreciated. Thank You! 5 people had this problem I have this problem too Labels: Catalyst 2000 catalyst_2960 password ...
Enter host name [Switch]: jh_switch01 (京海第一路交换机,即FTE网络A交换机)The en able secret is a password used to protect access toprivileged EXE C and configuration modes. This password, afterentered, becomes e ncrypted in the configuration.Enter enable secret(要求输入特权模式进入密令): T...
Switch#show interfaces interface-id switchport 查看端口详细配置 Switch#copy running-config startup-config 保存配置 批量端口加入特定Vlan的命令 int range fa0/1 - 10 switchport access VLan V2 将特定端口设为trunk 2960-01(config)#default interface fastEthernet 0/1 端口恢复默认值 2960-01(config)#inter...
switch#configure terminal (进入配置状态) Switch(config)#hostname 配置的交换机姓名 如:30FLoor-2960-1 30FLoor-2960-1(config)#end 30FLoor-2960-1# 2)配置交换机的ip 30FLoor-2960-1#configure terminal (进入配置状态) 30FLoor-2960-1(config)#interface vlan 1 ...
Switch#copy running-config startup-config保存配置 cisco2960口令恢复 交换机口令恢复的步骤 ⒈串口线连接到到交换机的console口。 ⒉先按住交换机面板上的mode键,然后打开电源。 ⒊初始化flash。 >flash_init ⒋更名含有password的配置文件。 >rename flash:config.text flash:config.old ...
3. 进入Cisco 2960系列交换机的初始配置模式 启动终端仿真软件,并打开与交换机的连接。 基本配置 交换机模式介绍: switch> 用户模式 switch>enable 进入特权模式 switch# 特权模式 switch#config terminal 进入配置模式 switch(config)# 配置模式 输入命令进入全局配置模式: ...
Switch(config-if)# 2、基本操作 #全局模式下修改交换机名称 Switch(config)#hostname test01(交换机名称) #全局模式下设置登陆特权加密密码 Switch(config)#enable secret 123456 #全局模式下设置登陆特权非加密密码 Switch(config)#enable password 123456 ...
21配置步骤注释 配置密码Switch>en特权模式Switch#conf t 配置模式Switch(config)#host SAT2960改变设备名称Switch(config)#ena se cisco特权口令Switch(config)#line vty 0 15修改远程登陆 口令Switch(config-line)#loginSwitch(config-line)#password ciscoSwitch(config-line)#line con 0修改串口登陆口令Switch(...
Switch#show running-config查看配置 Switch#copy running-config startup-config保存配置 cisco2960口令恢复 交换机口令恢复的步骤 ⒈串口线连接到到交换机的console口。 ⒉先按住交换机面板上的mode键,然后打开电源。 ⒊初始化flash。 >flash_init ⒋更名含有password的配置文件。
Cisco model: WS-C2960X-24TS-L Version ID: V02 Software: 15.0(2)EX5 Programming Once connected with the serial cable (default settings are 9600 baud), you should be able to see messages on the screen as the switch boots. This will confirm that your serial cable is working correctly. ...