Tensile Strength, Ultimate 565 MPa 81900 psi Tensile Strength, Yield 310 MPa 45000 psi Elongation at Break (in 50 mm) 16.0 % 16.0 % Reduction of Area 40.0 % 40.0 % Modulus of Elasticity (Typical for steel) 200 GPa 29000 ksi Bulk Modulus (Typical for steel) 140 GPa 20300 ksi Poissons ...
Standard Specification for Inch Series Machine Screws, Carbon Steel, 60 000 psi Tensile Strengthdoi:ASTM F2403-051.1本规范涵盖了标称直径为0000至3/4英寸的非热处理碳钢机螺钉的要求.最小极限抗拉强度为6000psi.F16.06F.
Tensile Strength, Ultimate550MPa79800psi Tensile Strength, Yield280MPa40600psi Elongation at Break25 %25 % Reduction of Area34 %34 % Modulus of Elasticity190GPa27600ksi Poissons Ratio0.290.29 Fatigue Strength200MPa29000psi Shear Modulus73.0GPa10600ksi ...
Tensile strength, yield 490 MPa 71100 psi Modulus of elasticity 200 GPa 29007 ksi Bulk modulus (typical for steel) 140 GPa 20300 ksi Shear modulus (typical for steel) 80 GPa 11600 ksi Poissons ratio (typical for steel) 0.27-0.30 0.27-0.30 Elongation at break (in 50 mm) 10% 10% Reductio...
[translate] aThe friend is doing any 朋友做着其中任一[translate] ahebegebuehr 正在翻译,请等待...[translate] acarbon steel bolts and studs,60000 psi tensile strength 碳钢螺栓和螺柱, 60000 psi抗拉强度[translate]
Cold Drawn 1018 Carbon SteelHot Rolled 1018 Carbon SteelMechanical Properties Brinell Hardness 130 to 140 Elastic (Young's, Tensile) Modulus 190 GPa 27 x 106 psi Elongation at Break 17 to 27 % Fatigue Strength 180 to 270 MPa 26 to 38 x 103 psi Poisson's Ratio 0.29 Reduction in Area 45...
ASTM A321 carbon steel is a carbon (non-alloy) steel formulated for primary forming into wrought products. Cited properties are appropriate for the quenched and tempered condition. It has a moderately high tensile strength among the wrought carbon or non-alloy steels in the database. The graph ...
21 [ISO] ISO 3506-3 - 2009 Mechanical properties of corrosion resistant stainless steel fasteners— Part 3:Set screws and similar fasteners not under tensile stress 22 [ASME] ASME B 18.6.3 (T4.11.3-1) - 2024 Torsional Strength Requirements for Tapping Screws 23 [ASME/ANSI] ASME/ANSI ...
1.A36 SS400 steel is a medium tensile steel supplied in the black hot rolled or normalized condition. It has a tensile strength of 570 - 700 MPa and Brinell hardness ranging between 170 and 210. 2.AISI 1045 steel is characterized by good weldability, good machinability, and high s...
Tensile strength, min, psi (MPa) 48,000 (330) 60000 (415) 70,000 (485) Yield strength, min, psi (MPa) 30,000 (205) 35,000 (240) 40,000 (275) (Note: This is summarized information from ASME Specification A106. Please refer to the specific Standard or Specification or contact us ...