6.在gbw的基础上同样可以得到相位裕度PM的表达式,首先将上一步的GBW表达式送入stack中,再将相频曲线送入calculator中,如下图所示; 7. 在function panel中选择"value"函数,可得到相频曲线在特定频率的相位值。根据相位裕度定义,x轴取值即为GBW所在频率,将其填入,其余设置默认,然后点击apply即可,如下图; 8.由于相...
Calculator窗口中的按钮可以分为下面几个部分: 1.功能键选(择、打印波形曲线,绘波形图); 2.常规计算器键盘; .函数键。 下面分别介绍他们的功能。 功能键: 1.browser:打开结果浏览窗口R(esultBrowser)。它有如下作用: o观察模拟波形和文本结果 o绘制波形 。将波形表达式直接拷入计算器窗口中 2.wavefamily:从波...
左上角reset GUI
Calculator 窗口中的按钮可以分为下面几个部分: 1. 功能键(选择,打印波形曲线,绘波形图); 2. 常规计算器键盘; 3. 函数键. 下面分别介绍他们的功能. 第 16 页共 97 页 Cadence cdsSPICE 使用说明 一.功能键: 1.browser:打开结果浏览窗口(Result Browser). 2.wave,family:从波形窗口(waveform Window)中...
Now I try to integrate the function in the calculator by the help of the function 'procedure( f1() Matching_Skill )'. When I push the 'f1'-button in the Calculator it makes something but it doesn't return a value or a error warning (this means it works or not?). I ...
the greater the accuracy of the frequency measurement to the long term average at that control voltage. You can view the frequency settling behavior from a transient simulation if you measure the instantaneous frequency using the Calculator freq() function. Do not use the frequency() function as ...
如果表达式比较复杂,还可以点击 Calculator 栏的 open 按钮,打开 Calculator(后面还会详细介绍使用方法) ,在其中编辑好表达式后, 在上图窗口中点击 Calculator 栏的 Get Expression 按钮,表达式就会被截取到 Expression 栏。 6 . 仿真过程 所有设置都完成后,点击菜单 SimulationNetlist Run 或者点击按钮 ;如果电路 没...
Calculator窗口中的按钮可以分为下面几个部分:1. 功能键(选择、打印波形曲线,绘波形图);2. 常规 49、计算器键盘;3. 函数键。下面分别介绍他们的功能。一.功能键:1. browser :打开结果浏览窗口( Result Browser )。它有如下作用:。观察模拟波形和文本结果。绘制波形。将波形表达式直接拷入计算器窗口中2. wave...
Calculator窗口中的按钮可以分为下面几个部分:功能键(选择、打印波形曲线,绘波形图);常规计算器键盘;函数键。下面分别介绍他们的功能。一.功能键: 1.browser:打开结果浏览窗口(Result Browser)。 2.wave、family:从波形窗口(waveform Window)中选择所要处理的曲线波形。Wave是选择单一的波形,family是选择一组波形(如...
3. In the calculator , choose Special Functions and specify a certain frequency, say 1 Hz, to get a value at that frequency. Pick reasonable frequency. This function will calculate the interpolation. I will simulate 1Hz to 2Hz for 1Hz step, then plot at 1Hz. This is en...