kvm + 网卡bonding + bridge桥 有这种情况,linux系统上做了网卡的绑定(bonding), 又装了kvm虚拟机,因为kvm又需要配置bridge(桥),所以需要把bonding和bridge结合起来,这里做个记录 1、环境: 系统: Centos7 物理网卡接口: em1、em2 bridge接口: br0 172.16.0.183 bond接口: bond0 注:ip是配置在br0桥接口上 2...
nmcli connection add con-name bond0 ifname bond0 type bond mode active-backup ip4 172.25.254.220/24 添加bond类型的bond0并且设定好ip地址。这时候所有网卡信息都存放在 /proc/net/bonding/bond0下 watch -n 1 cat /proc/net/bonding/bond0 ---监控bond0下的网卡工作情况 nmcli connection add con-name...
nmcli connection add con-name bond0 ifname bond0 type bond mode active-backup ip4 172.25.254.220/24 添加bond类型的bond0并且设定好ip地址。这时候所有网卡信息都存放在 /proc/net/bonding/bond0下 watch -n 1 cat /proc/net/bonding/bond0 ---监控bond0下的网卡工作情况 nmcli connection add con-name...
nmcli connection add con-name bond0 ifname bond0 type bond mode active-backup ip4 172.25.254.220/24 添加bond类型的bond0并且设定好ip地址。这时候所有网卡信息都存放在 /proc/net/bonding/bond0下 watch -n 1 cat /proc/net/bonding/bond0 ---监控bond0下的网卡工作情况 nmcli connection add con-name...
CentOS系统Bonding+VLAN+Bridge配置 由于业务的需要,需要在我们的一台虚拟化机器上,实现如下的配置: 首先,需要将两块网卡设置Bonding并配置交换机对应端口trunk模式;在此基础上,添加宿主机的IP地址,并添加相应的VLAN,最后,还需要添加一个Bridge,用于桥接创建的虚拟机。
包括mode5,由ARP协商完成接收的负载。bonding 驱动程序截获 ARP 在本地系统发送出的请求,用其中之一的硬件地址覆盖从属设备的原地址。就像是在服务器上不同的人使用不同的硬件地址一样,不需要交换机做链路聚合。 ——— 版权声明:本文为CSDN博主「木下-
KVM之Bonding+Bridge实验 KVM Server端Bonding+Bridge配置 [root@localhost~]# more /etc/sysconfig/network-scripts/ifcfg-em2 DEVICE=em2 ONBOOT=yes BOOTPROTO=static USERCTL=no MASTER=bond0 SLAVE=yes [root@localhost~]# more /etc/sysconfig/network-scripts/ifcfg-em3...
KVM之Bonding+Bridge实验 测试环境: KVM Server端Bonding+Bridge配置 [root@localhost~]# more /etc/sysconfig/network-scripts/ifcfg-em2 DEVICE=em2 ONBOOT=yes BOOTPROTO=static USERCTL=no MASTER=bond0 SLAVE=yes [root@localhost~]# more /etc/sysconfig/network-scripts/ifcfg-em3...
nmcli实现bonding 1 . 新建bond0配置文件 nmcli connection add type bond con-name bond0 ifname bond0 mode active-backup type指定bond类型,con-name为配置文件连接名,ifname为指定接口,mode为选定bond工作模式 2 . bond0添加IP地址 nmcli connection modify bond0 ipv4.method manual ipv4.addresses 192.168.198...
The clamping device for the bridge bonding plate facilitates rapid fixing and is rapid and convenient to fasten, simple in structure, easy to operate and capable of saving time.王海涛高宇熊慧中