Arduino:1.8.5 (Windows 10), 开发板:"Arduino/Genuino Uno"项目使用了 3652 字节,占用了 (11%) 程序存储空间。最大为 32256 字节。全局变量使用了313字节,(15%)的动态内存,余留1735字节局部变量。最大为2048字节。avrdude: stk500_recv(): programmer is not respondingavrdude: stk500_getsync() attempt...
Maximum is 2048 bytes.avrdude: stk500_recv(): programmer is not respondingavrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x85avrdude: stk500_recv(): programmer is not respondingavrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x85avrdude: stk500_recv(): ...
本吧热帖: 1-为什么在vscode上编译下载arduino代码后输出乱码? 2-有没有大佬知道这个开发板怎么和LCD显示屏还有温湿度显示器连接 3-大佬们救命 4-大学生找代做 5-求知,有偿! 6-大佬们救命一下 7-如何使用国产arduino UNO r3开发板自带硬串口tx rx? 8-求电气图和pcb文件
android、bluetooth、arduino-uno sync: avrdude: stk500_recv(): programmer is not responding avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt avrdude: stk500_getsync() attempt 5 of 10: not in 浏览231提问于2017-11-17得票数 -1 14回答 avrdude: stk500v2...
it compiles fine on the mega 256 but not on the 1284p. i tried altering the library files so the 1284 is in the susported list but thats as far as i could do as im no programmer. this was suggested on another site but didnt work, i still get the sam error Reply Dominic ...
之前试过用uno给他烧引导程序了,这样应该是烧好了吧 贴吧用户_54tKKJy 锋芒毕露 3 Arduino:1.8.9 (Windows Store 1.8.21.0) (Windows 10), 开发板:"Arduino Nano, ATmega328P (Old Bootloader)"avrdude: stk500_recv(): programmer is not respondingavrdude: stk500_recv(): programmer is not respon...
本人买的国产Arduino Leonardo,连接上电脑之后程序无法导入,编译成功之后显示正在上传,不报错,很久很久之后会报错: Connecting to programmer: .avrdude: butterfly_recv(): programmer is not respondingavrdude: butterfly_recv(): programmer is not respondingavrdude: butterfly_recv(): programmer is not responding...
本吧热帖: 1-【arduino】哥救救孩子吧 2-想问几个问题 3-接上文// 4-大佬们,小白上传程序一直出现这个报错怎么解 5-新手小白求助 6-各位老师怎么编写一个智能晾衣架的程序 7-Arduino控制震动马达问题 8-UnoR4使用定时中断功能 9-大佬们救命一下 10-求求吧友们,路径不存在
由前面介绍可知,这里应该是将ISP板的引脚连接到目标板上的ICSP接口上去,连接对应表如下(以使用UNO作为ISP板为例) 实际连接电路如下所示,其中左边是ISP板,连接到电脑上,右边是等待下载bootloader的目标板 使用arduino IDE为目标板烧写bootloader 按照前面的方式连接好ISP板和目标板后,将ISP板连接到电脑上,打开IDE,首先...
Note that the Arduino Uno, Nano, and Mega are missing from this list. Those three boards do not have native USB support and will not work for this. You will need to buy another microcontroller. Sorry Charlie Software The next thing you’ll need is the software to make this work. There...