@文心快码arduino programmer is not responding 文心快码 当遇到“Arduino programmer is not responding”的问题时,可以按照以下步骤进行排查和解决: 检查Arduino编程器与电脑的连接: 确保Arduino编程器(如AVR ISP、USBasp等)已正确连接到电脑的USB端口。 检查连接线是否有损坏或接触不良的情况。重启Arduino编程器和电脑...
Arduino:1.8.5 (Windows 10), 开发板:"Arduino/Genuino Uno"项目使用了 3652 字节,占用了 (11%) 程序存储空间。最大为 32256 字节。全局变量使用了313字节,(15%)的动态内存,余留1735字节局部变量。最大为2048字节。avrdude: stk500_recv(): programmer is not respondingavrdude: stk500_getsync() attempt...
只要出现了:avrdude: stk500_recv(): programmer is not responding这段话,就可以继续看了,否则 ...
Arduino:1.8.5 (Windows XP), 开发板:"Arduino/Genuino Uno"项目使用了 926 字节,占用了 (2%) 程序存储空间。最大为 32256 字节。全局变量使用了9字节,(0%)的动态内存,余留2039字节局部变量。最大为2048字节。avrdude: stk500_recv(): programmer is not respondingavrdude: stk500_getsync() attempt 1 ...
Arduino:1.8.13 (Windows Store 1.8.42.0) (Windows 10), 开发板:"Arduino Uno" 项目使用了 924 字节,占用了 (2%) 程序存储空间。最大为 32256 字节。 全局变量使用了9字节,(0%)的动态内存,余留2039字节局部变量。最大为2048字节。 avrdude: stk500_recv(): programmer is not responding avrdude: stk500...
Arduino:1.8.13(Windows Store1.8.42.0)(Windows10),开发板:"Arduino Uno"项目使用了924字节,占用了(2%)程序存储空间。最大为32256字节。全局变量使用了9字节,(0%)的动态内存,余留2039字节局部变量。最大为2048字节。 avrdude:stk500_recv():programmer is not responding ...
Maximum is 32256 bytes.Global variables use 482 bytes (23%) of dynamic memory, leaving 1566 bytes for local variables. Maximum is 2048 bytes.avrdude: stk500_recv(): programmer is not respondingavrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x85avrdude: stk500_recv(): ...
avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x00 我以为是USBISP烧录器把328P的BOOTLOADER弄坏了,就扣掉UNO上的328P,换了一片写好BOOTLOADER和LED发光的程序的328P。 换上去以后,UNO上自带的LED灯在闪烁,说明芯片工作正常。 然而...
然后用UNO作为烧录器尝试烧录bootloader出现了大量的错误提示如下:avrdude: stk500_recv(): programmer is not respondingavrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x03avrdude: stk500_recv(): programmer is not respondingavrdude: stk500_getsync() attempt 2 of 10: not in sync:...
Uno只有一种处理器不需要选,Nano处理器有2个版本,新的选ATmega328P,旧的选ATmega328P (old bootloader)。 如果上传失败,提示"avrdude: stk500_recv(): programmer is not responding",一般都是处理器版本不对,切换成另一个试试。 4)指定端口 如不清楚是哪个,到设备管理器里查看。进口原装板的驱动在安装IDE时...