在Arduino编程中,打印信息到串行监视器(Serial Monitor)是调试和监控程序运行的重要工具。Arduino IDE 提供了一系列用于串行通信的函数,其中最常用的就是 Serial.print() 和Serial.println()。以下是对这些函数的详细介绍和使用示例: 1. 初始化串行通信 在使用任何串行打印函数之前,你需要先初始化串行端口并设置波特率...
Upload above sketch, enter some data and look at the serial monitor to see what Arduino received. Fig. 1 shows the data received by Arduino in (Decimal)(Hex)(Character) format. You can repeat the same by changing the modes of the serial monitor. Set the serial monitor to ‘no line end...
Serial.print(F("Status: 0x")); Serial.println(finger.status_reg, HEX); Serial.print(F("Sys ID: 0x")); Serial.println(finger.system_id, HEX); Serial.print(F("Capacity: ")); Serial.println(finger.capacity); Serial.print(F("Security level: ")); Serial.println(finger.security_level)...
Serial Monitor——在新窗口打开串口监视器(见下一节中的图1-9)。 主屏幕下方有两个窗口。第一个窗口提供了状态信息和反馈,第二个窗口在你校验和烧写程序时提示相关信息。编码的错误也会在这里显示。 图1-8 一个典型的程序,其中标注了按钮和屏幕上的一些区域 代码编辑器会自动匹配花括号{},用来标示代码块,...
Describe the request Add a mode to Serial Monitor for printing hexadecimal data. Describe the current behavior Serial Monitor does not support interpreting data as hexadecimal. Arduino IDE version d6a4b0f Operating system All Operating s...
问使用Arduino串行监视器和嵌套循环与不同的外围设备通信EN一、安装树莓派及arduino开发环境 搭建树莓...
Serial.print(tab[key%16],BYTE); } press = 0; key = 0; } 把程序编译后烧进Arduino,然后把按下Arduino编程软件的Serial Monitor按钮,在代码窗口下面就会显示出串口监视器的串口,在下拉列表中把波特率改为9600即我们设置的通信波特率。然后按下键盘上的按钮,就能在窗口中看到对应的键值被发送过来了。
// byte. The serial monitor interprets all bytes as // ASCII, so 33, the first number, will show up as '!' Serial.write(thisByte); Serial.print(", dec: "); // prints value as string as an ASCII-encoded decimal (base 10). ...
MONITOR_SERIAL.print(radar.firmware_minor_version); MONITOR_SERIAL.print('.'); MONITOR_SERIAL.println(radar.firmware_bugfix_version, HEX); } else { MONITOR_SERIAL.println(F("not connected")); } } voidloop() { radar.read(); if(radar.isConnected() && millis() - lastReading > 1000)/...
20、a1.print1n("He11oWorld!");de1ay(1000);在将工程下载到Arduino模块中之后,在Arduino集成开发环境的工具栏中单击“SerialMonitor”控制,打开用口监视器画囹国画B丽接着将波特率设置为9600,即保持与工程中的设置相一致如果一切正常,此时我们就可以在Arduino集成开发环境的Console窗口中看到用口上输出的数据了950...