Serial.println(my_str);//(3) 字符串对象重写my_str ="My new string."; Serial.println(my_str);//(4) 字符串内容替换my_str.replace("string","Arduino sketch"); Serial.println(my_str);//(5) 获取字符串对象的长度Serial.print("String length is:"); Serial.println(my_str.length()); }...
Serial input: accepts serial input, displays it. 串行输入:接收串行输入,显示它。 SetCursor : set the cursor position. SetCursor:设置光标位置。 Autoscroll : shift text right and left. 自动滚屏:移文本左,右。 SPI Library SPI库 BarometricPressureSensor: read air pressure and temperature from a senso...
Serial.begin(9600);//Allow Serial communication via USB cable to computer (if required)pinMode(RxD, INPUT);//Setup the Arduino to receive INPUT from the bluetooth shield on Digital Pin 6pinMode(TxD, OUTPUT);//Setup the Arduino to send data (OUTPUT) to the bluetooth shield on Digital Pin ...
Serial.begin(9600); Serial.println("Hello world!"); The second line of code transmits ‘Hello World’ via the serial port (in this case, it will pass through the Arduino’s serial-to-USB interface so your computer can read it). This mean the serial port’s output is being pipe...
本次研究第 03 个示例:01.Basics - Blink (1)示例列表 格瑞图:Arduino-0001-安装 Arduino IDE 1.8.19 格瑞图:Arduino-0002-内置示例-模拟读 Analog Read Serial 格瑞图:Arduino-0003-内置示例-最简化代码 Bare Minimum 1、示例代码及解析 (1)代码
--- C语言编程官方案例 1.基础知识 Basics Analog Read Serial:读取电位计,将其状态输出到Arduino串行口监视器。...Bare Minimum:启动Arduino所需的最少代码。 Blink:打开和关闭LED。 Digital Read Serial:读取开关量,将状态发布到Arduino串行监视器。...还有Max / MSP补丁也可以与每个Arduino进行通信。有关Max...
pinMode(pullDown, INPUT); } void loop() { // read buttons states int buttonUpState = digitalRead(pullUp); int buttonDownState = digitalRead(pullDown); // make a message that will be sent to the serial line String message = “Pull Up: ” + String(buttonUpState); ...
图2-1 数字信号示例 串口监视器效果打开Arduino IDE,选择菜单中的文件(File) -- 示例(Examples) -- 01 Basics – DigitalReadSerial 代码。 代码如下: int pushButton = 2; // 连接到数字引脚2void setup() { //初始化函数Serial.begin(9600); //设置串口波特率pinMode(pushButton, INPUT); //设置按键为...
参数:pin 要设置的引脚,mode OUTPUT , INPUT eg: 比如我们写一段,流水灯的代码,在使用之前, 我们需要将连接的引脚设置为OUTPUT才可以使用哦 连接如下电路图,我们就连接好了一个灯泡了 由于灯泡我们设置的 Arduino UNO 的开发板的 A4 引脚,因此我们只需要在 setup() 函数中写下如下一行代码即可 ...
{Serial.begin(9600);//初始化串口通信,波特率为 9600pinMode(AVD_PIN,INPUT);//将 AVD_PIN 设置为输入模式pinMode(LED_PIN,OUTPUT);//将 LED_PIN 设置为输出模式pinMode(BU_PIN,OUTPUT);//将 BU_PIN 设置为输出模式}voidloop(){int state=digitalRead(AVD_PIN);//读取 AVD_PIN 引脚的状态(高电平或...