Create a connection to Arduino hardware and read digital pin 13. a = arduino; readDigitalPin(a,'D13') ans = 1 Input Arguments collapse all Arduino hardware connection created usingarduino, specified as an object. Pin number on the physical hardware, specified as a character vector. ...
Reads a digital input on pin 2, prints the result to the serial monitor This example code is in the public domain. */ 2. 变量定义 // digital pin 2 has a pushbutton attached to it. Give it a name: int pushButton = 2; 定义了一个变量pushButton,并将其赋值为2。这表示代码将操作数字...
digital Read(PIN) 参数: pin:你想读取的引脚号(int) 返回 HIGH或LOW 例子: led Pin=13//LED连接到13脚 intinPin=7;//按钮连接到数字引脚7 intval=0;//定义变量存以储读值 voidsetup() { pin Mode(led Pin, OUTPUT) ;//将13脚设置为输出 pin Mode(inPin, INPUT) ;//将7脚设置为输入 voidloop(...
数字I/O 函数 Digital I/O Functions pinMode(): 描述:将指定的引脚配置为输入或者输出的模式 函数原型:pinModel(pin,mode) 参数: pin:要设置其模式的引脚编号 mode:INPUT(输入模式),OUTPUT(输出模式),INPUT_PULLUP(上拉输入模式) 返回值:无 digitalRead(): 描述:读取指定数字引脚的值 函数原型:digitalRe...
}voidloop() {//read the state of the pushbutton value:buttonState =digitalRead(buttonPin);//check if the pushbutton is pressed. If it is, the buttonState is HIGH:if(buttonState ==HIGH) {//turn LED on:digitalWrite(ledPin, HIGH); ...
当读取(read) 或写入(write) 数字引脚时只有两个可能的值:HIGH和LOW。 HIGH HIGH(参考引脚) 的含义取决于引脚(pin) 的设置, 引脚定义为INPUT或OUTPUT时含义有所不同。当一个引脚通过pin Mode被设置为INPUT, 并通过digital Read读取(read) 时。如果当前引脚的电压大于等于3V,微控制器将会返回为HIGH。引脚也可以...
Arduino Mega 2560的数字IO引脚编号从0到53,其中0和1通常用于串行通信,而一些引脚还支持PWM输出。基本输入输出操作:输入操作:要将一个引脚设置为输入,可以使用pinMode函数,其中pin是你想要设置为输入的引脚编号。之后,可以使用digitalRead函数读取该引脚的电平状态。输出操作:要将一个引脚设置为输出,...
pinMode() digitalRead() delay() int serial DigitalPins AnalogReadSerial - 读取电位计,并打印它的状态到Arduino串口监视器 BareMinimum - 需要开始一个新的程序的最简框架 Blink - 使LED灯开和关 DigitalReadSerial - 读取一个开关,打印其状态到Arduino串口监视器 ...
pinMode() digitalRead() delay() int serial DigitalPins Blink Without Delay: 不用delay()函数,使LED灯闪烁 Button: 用一个按钮来控制LED灯 Debounce: 读取一个按钮,并滤掉噪音 Button State Change: 记录按键按下的次数 Input Pullup Serial: 示范怎么用pinMode()来上拉引脚 ...
pinMode() digitalWrite() digitalRead() if else BlinkWithoutDelay - 闪烁一个LED灯而不使用delay()函数延时 Debounce - 读取一个按键状态,并滤掉噪音 DigitalInputPullup - 示范用pinmode()来定义上拉输入引脚 StateChangeDetection - 记录按键按下的次数 ...