当遇到Arduino IDE中的avrdude错误提示“stk500_recv(): programmer is not responding”时,通常表示编程器(programmer)无法与Arduino板通信。以下是解决此问题的几个步骤: 确认芯片选择正确: 确保在Arduino IDE中选择的板卡型号与实际使用的板卡型号相匹配。检查...
最近想起我还有块Arduino Nano,心血来潮想玩玩,然后avrdude: stk500_recv(): programmer is not responding 00:22 这个0x64可能是0x后面接一个十六进制的两位数,只要出现了:avrdude: stk500_recv(): programmer is not responding这段话,就可以继续看了,否则 先确认芯片选对没(没选对的愣着干啥,赶紧改啊) ...
avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x1bavrdude: stk500_recv(): programmer is not respondingavrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0x1bavrdude: stk500_recv(): programmer is not respondingavrdude: stk500_getsync() attempt 4 of 10: ...
CH340 改版的非原装arduino Nano在写入程序时可能会报错。错误如下：avrdude: stk500_recv(): programmer is not respondingavrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0xf6avrdude: stk500_recv(): programmer is not respondingavrdude: stk500_getsync() attempt 2 of 10: not in sy...
avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0x01avrdude: stk500_recv(): programmer is not respondingavrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0x01上传出错。查看页面 http://www.arduino.cc/en/Guide/Troubleshooting#upload 获取建议。报告将会包含更多的...
Arduino报错 avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x01 avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x01...
(): programmer is not responding avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0xa9 avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0xa9 avrdude: stk500_recv(): programmer is not responding avrdude: ...
avrdude: stk500_recv(): programmer is not respondingavrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0x03上传出错。查看页面 http://www.arduino.cc/en/Guide/Troubleshooting#upload 获取建议。avrdude: stk500_recv(): programmer is not respondingavrdude: stk500_getsync() attempt 10...
【arduino】程..avrdude: stk500_recv(): programmer is not respondingavrdude: stk500_getsync() attempt 1 of 10: not i
烧录好引导程序后,上传程序失败。显示avrdude: stk500_recv(): programmer is not responding。···后面很长 确定328P芯片没问题。对比好的Arduino测电压,确定Pin10_RXLED,pin11_TXLED电压异常。重新焊一次,还是不能上传。用一块好的板把所有引脚出问题的情况记录下来,确定是13pin_GND引脚的问题。最后发现13pin...