控制LED闪烁:代码通过控制数字引脚13(大多数Arduino板上连接了一个内置LED)的电平高低,使LED灯以1秒亮、1秒灭的频率不断闪烁。 代码逐行解释 1. 注释部分 功能:让一个LED灯每秒闪烁一次,即亮1秒,灭1秒,不断重复。 /* Blink Turns on an LED on for one second, then off for one second, repeatedly. This...
Blink*/// 在大多数Arduino控制板上 13号引脚都连接了一个标有“L”的LED灯// 我们给13号引脚设置一个别名“led”int led = 13;//在板子启动或者复位重启后, setup部分的程序只会运行一次void setup(){ // 将“led”引脚设置为输出状态 pinMode(led, OUTPUT);}//setup部分程序运行完后,loop部分的程序...
2、Blink.ino中用到的几个函数: ① pinMode(pin,mode) : 将指定的引脚配置为输入或输出 - pin : 所需要设置的引脚号 - mode : INPUT/OUTPUT(pinMode也可以是INPUT_PULLUP,使用引脚内置的上拉电阻) pinMode(LED_BUILTIN, OUTPUT); ② digitalWrite(pin,HIGH/LOW) : 数字引脚输出,HIGH表示高电平(5v),LO...
准备完毕,现在让我们在Arduino IDE中写入程序吧。由于是LED闪烁程序,所以我们先打开草图示例中的“01.Basics”-“Blink”程序。打开程序后,请在“Tools”中将开发板设置为“ESP32 Dev Module”并写入程序。 程序写入完成后,LED灯成功实现闪烁! (由于此次指定了引脚13,因此将LED连接到ESPr Developer 32上的引脚13和G...
PlatformIO 接口将在编程 Arduino UNO 的同时进行讲解。在这里,我们正在使用 PlatformIO 对 Arduino 进行编程以使 LED 闪烁。使用 Arduino IDE也可以做到这一点。按照以下步骤创建一个用于闪烁 LED 的新项目。 从快速访问菜单中选择“新建项目”选项卡。 为项目命名(此处为“Blink”)。搜索并选择 Arduino UNO 板。由...
https://www.arduino.cc/en/Tutorial/BuiltInExamples/Blink */ // the setup function runs once when you press reset or power the board void setup() { // initialize digital pin LED_BUILTIN as an output. //初始化芯片上led灯的输出,这里的LED_BUILTIN就是内部led灯的gpio的别名,第二个参数指明...
setup函数只运行一次用来启动arduino控制器将运行中不改变的数值和属性固化到芯片中voidsetupinitializedigitalpinledbuiltinasanoutput 【 Arduino学习笔记 02】第一个 Arduino项目 ——点亮 LEDBlink.ino程 序。。。 /* Blink Turns an LED on for one second, then off for one second, repeatedly. */ // ...
https://www.arduino.cc/en/Tutorial/BuiltInExamples/BlinkWithoutDelay */ (3)全局变量及设置函数 // constants won't change. Used here to set a pin number: 常量不会被改变。这里用来定义针脚编号: const int ledPin = LED_BUILTIN;// the number of the LED pin ...
实测中确实是这样,在 A6、A7 引脚上,想运行 Blink 例程,使用 pinMode(A6, OUTPUT),digitalWrite(A6, HIGH) 都不会得到你所需要的效果。更崩溃的是,你可能改变了芯片内部你原本不想改变的寄存器配置,没准会有诡异意外发生。玩 Nano,或者是贴片AVR的 Arduino 朋友们,可要注意。
* After upload the LED on the board should start to flash slowly (on for1sec off for1sec) * * Open the SerialMonitorandfollow the on screen instructions * * If the version of the bootloader that is containedinthis sketch is already installed, ...