http://www.arduino.cc/en/Tutorial/InputPullupSerial This example code is in the public domain */ void setup() { //start serial connection Serial.begin(9600); //configure pin2 as an input and enable the internal pull-up resistor pinMode(2, INPUT_PULLUP); pinMode(13, OUTPUT); } void...
2、数字输入上拉 DigitalInputPullup - 输出上拉串口 InputPullupSerial This example demonstrates the use of INPUT_PULLUP with pinMode(). It monitors the state of a switch by establishingserial communicationbetween your Arduino and your computer over USB. 本例演示如何使用 pinMode 和 INPUT_PULLUP。
INPUT_PULLUP:将引脚输入模式内部拉高(是让引脚保持高电平的状态) 拉低:是给引脚接一个电阻到GND接地,让引脚保持在一个低电平的状态 第二种方法是digitalRead(pin)作用是读取指定引脚的电平状态 第三种方法是digitalWrite(pin,MODE)作用是将指定引脚输出高电平或者低电平 特殊IO口:IO口以~加数字开头的是可以进行模...
pin:要设置其模式的引脚编号 mode:INPUT(输入模式),OUTPUT(输出模式),INPUT_PULLUP(上拉输入模式) 返回值:无 digitalRead(): 描述:读取指定数字引脚的值 函数原型:digitalRead(pin) 参数:要读取的数字引脚的编号 返回值:HIGH(1),LOW(0) digitalWrite(): 描述:将数字 HIGH 或 LOW 的值写入数字引脚 函数原型:...
pinMode(buttonPin,INPUT); 改为 pinMode(buttonPin,INPUT_PULLUP); 就可以使用引脚内部的上拉电阻。这个电阻也很大,一般为20~50kΩ。它也可以稳定电平,并可以稳定在高电平。 如下程序可实现按一下按键灯开,再按一下灯灭。 intbuttonPin=2;intledPin=13; ...
Using an external resistor instead of Arduino INPUT_PULLUP Pull up resistor Instead of using the internal pull up resistor from your Arduino board, you could decide to create the circuit yourself and add an external pull up resistor. Your circuit will look like this. ...
INPUT_PULLUP 表示让某一个IO引脚作输入,反之, OUTPUT则使一个IO引脚做输出 INPUT_PULLUP则配置一个IO引脚具有上拉输入功能(上拉电阻的目的是为了保证在无信号输入时输入端的电平为高电平),从英文意思也能很直观的看出来。 理解了pinMode()函数,digitalWrite()就很容易理解啦,value的取值有两个HIGH、LOW,HIGH表...
您只需在第4行的数字引脚模式设置中指定“INPUT_PULLUP”即可。这样就能激活内置的上拉功能,从而能够在未按下按钮的状态下稳定HIGH输入。请注意,Arduino Uno中未内置下拉功能。 按下开关时点亮LED 开关的输入还可用来控制其他电子元器件。在这里,让我们利用Arduino中安装的LED(引脚13),尝试实现在按下开关时点亮LED...
pinMode(2,INPUT_PULLUP);//将2号管脚设置为输入并且内部上拉模式 pinMode(12,OUTPUT); } voidloop() { intn =digitalRead(2);//创建一个变量n,将4号数字口的状态采集出来赋值给他。 if(n==LOW)//判断n是否为低电平,如果是执行下面的语句,不是则跳过。