http://www.arduino.cc/en/Tutorial/InputPullupSerial This example code is in the public domain */ void setup() { //start serial connection Serial.begin(9600); //configure pin2 as an input and enable the internal pull-up resistor pinMode(2, INPUT_PULLUP); pinMode(13, OUTPUT); } void...
您只需在第4行的数字引脚模式设置中指定“INPUT_PULLUP”即可。这样就能激活内置的上拉功能,从而能够在未按下按钮的状态下稳定HIGH输入。请注意,Arduino Uno中未内置下拉功能。 按下开关时点亮LED 开关的输入还可用来控制其他电子元器件。在这里,让我们利用Arduino中安装的LED(引脚13),尝试实现在按下开关时点亮LED,...
pinMode(BUTTON_PIN, INPUT_PULLUP); } voidloop(){ Serial.println(digitalRead(BUTTON_PIN)); delay(10); } If you run this code and open the Serial Plotter, you’ll see that the default value is 1 (HIGH). When you press the button the state directly goes to 0 (LOW) and comes back...
mode:INPUT(输入模式),OUTPUT(输出模式),INPUT_PULLUP(上拉输入模式) 返回值:无 digitalRead(): 描述:读取指定数字引脚的值 函数原型:digitalRead(pin) 参数:要读取的数字引脚的编号 返回值:HIGH(1),LOW(0) digitalWrite(): 描述:将数字 HIGH 或 LOW 的值写入数字引脚 函数原型:digitalWrite(pin,value) 参...
pinMode(Button1, INPUT);//按钮1引脚设置为输入 pinMode(Button2, INPUT_PULLUP); //按钮2引脚设置为输入上拉模式 } void loop() { // 读取输入引脚的值 boolean button1State = digitalRead(Button1); boolean button2State = digitalRead(Button2); ...
思路:Arduino本身可以设置INPUT_PULLUP,而LINX中没有。猜测原因是LINX在具体实现中将PINMODE设置为INPUT,并且没有实现INPUT_PULLUP版本。因此只要修改LINX固件,增加PULLUP版本的实现即可。(如果不需要普通的浮空输入,直接把源代码里的INPUT改成INPUT_PULLUP即可,无须后续操作,这样所有能上拉的输入都会被上拉) ...
pinMode(2,INPUT_PULLUP); 把作为LED灯的pin13初始化为输出引脚: pinMode(13, OUTPUT); 现在初始化完成了,移入你代码的主循环里。当按钮被按下,5V电压会流过你的电路,而当它没有被按下,这个输入引脚就会链接到通过10k ohm电阻连接到地。这是数字输入,意味着开关只有开(1,或者高电平)和关(0,或者低电平...
pinMode(2,INPUT_PULLUP);//将2号管脚设置为输入并且内部上拉模式 pinMode(12,OUTPUT); } voidloop() { intn =digitalRead(2);//创建一个变量n,将4号数字口的状态采集出来赋值给他。 if(n==LOW)//判断n是否为低电平,如果是执行下面的语句,不是则跳过。
本次研究:02.Digital - DigitalInputPullup (1)示例列表 格瑞图:Arduino-0001-安装 Arduino IDE 1.8.19 格瑞图:Arduino-0002-内置示例-模拟读 Analog Read Serial 格瑞图:Arduino-0003-内置示例-最简化代码 Bare Minimum 格瑞图:Arduino-0004-内置示例-闪烁 Blink ...