数字引脚(Digital pins) 定义:INPUT和OUTPUT 数字引脚当作INPUT或OUTPUT都可以。用pin Mode() 方法使一个数字引脚从INPUT到OUTPUT变化。 引脚(Pins) 配置为输入(Inputs) Arduino(At mega) 引脚通过pin Mode() 配置为输入(INPUT) 即是将其配置在一个高阻抗的状态。配置为INPUT的引脚可以理解为引脚取样时对电路有...
10.1 HIGH|LOW(引脚电压定义) 10.2 INPUT|OUTPUT(数字引脚(Digital pins)定义) 10.3 true | false(逻辑层定义) 10.4 integer constants(整数常量) 10.5 floating point constants(浮点常量) 十一、数据类型 11.1 void 11.2 boolean(布尔) 11.3 char(有号数据类型) 11.4 unsigned char(无符号数据类型) 11.5 byte(...
const int analogInPin = A0; // Analog input pin that the potentiometer is attached to const int analogOutPin = 9; // Analog output pin that the LED is attached to int sensorValue = 0; // value read from the pot int outputValue = 0; // value output to the PWM (analog out) void...
10.1 HIGH|LOW(引脚电压定义) 10.2 INPUT|OUTPUT(数字引脚(Digital pins)定义) 10.3 true|false(逻辑层定义) 10.4 integerconstants(整数常量) 10.5 floating point constants(浮点常量) 十一、数据类型 11.1 void 11.2 boolean(布尔) 11.3 char(有号数据类型) 11.4 unsignedchar(无符号数据类型) 11.5 byte(无符号...
数字引脚当作INPUT 或 OUTPUT都可以 。用pinMode()方法使一个数字引脚从INPUT到OUTPUT变化。 引脚(Pins)配置为输入(Inputs) Arduino(Atmega)引脚通过pinMode()配置为 输入(INPUT) 即是将其配置在一个高阻抗的状态。配置为INPUT的引脚可以理解为引脚取样时对电路有极小的需求,即等效于在引脚前串联一个100兆欧姆(...
the pinMode() to INPUT_PULLUP to enable the internal pull-up resistor. See the digital pins ...
也正因为次,在 Arduino 的官方指南中提到,“The analog input pins can be used as digital pins, referred to as A0, A1, etc. ”。说的是,模拟输入口可以当数字口一样用。对于A0-A5来说,确实不错。但对于第一功能就是ADC(模数转换)而不兼有普通 IO 口功能的 ADC6 和 ADC7 来说。这句话就要打...
pinMode(2,INPUT_PULLUP); 把作为LED灯的pin13初始化为输出引脚: pinMode(13, OUTPUT); 现在初始化完成了,移入你代码的主循环里。当按钮被按下,5V电压会流过你的电路,而当它没有被按下,这个输入引脚就会链接到通过10k ohm电阻连接到地。这是数字输入,意味着开关只有开(1,或者高电平)和关(0,或者低电平...
pinMode(led, OUTPUT); 1. pinMode()函数,官方解释: Configures the specified pin to be have either as an input or an output . See the Digital Pins page for details on the functionality of the pins. 1. 2. 简单来说即设置引脚的模式为输入或者输出。函数内部被花括号括起来的部分将会被依次执行...
Arduino-语法手册 Arduino语法手册 Arduino的程序可以划分为三个主要部分:结构、变量(变量与常量)、函数。结构部分 一、结构 1.1setup()1.2loop()二、结构控制 2.1 if 2.2 if...else 2.3 for 2.4 switch case 2.5 while 2.6 do... while 2.7 break 2.8 continue 2.9 return 2.10 goto 三...