setup函数只能在Arduino板的每次上电或复位后运行一次。 INPUT- - OUTPUT- - RETURN- - Void Loop ( ) { } PURPOSE- 在创建了用于初始化并设置初始值的setup()函数后,loop()函数,正如它的名称所指,允许你的程序连续循环的更改和响应。可以使用它来主动控制Arduino板。 INPUT- - OUTPUT- - RETURN- - 3、A...
每次Arduino上电或重启后,setup函数只运行一次。 这里,初始化数字引脚为OUTPUT模式: pinMode(led, OUTPUT); 1. pinMode()函数,官方解释: Configures the specified pin to be have either as an input or an output . See the Digital Pins page for details on the functionality of the pins. 1. 2. 简...
http://www.arduino.cc/en/Tutorial/InputPullupSerial This example code is in the public domain */ void setup() { //start serial connection Serial.begin(9600); //configure pin2 as an input and enable the internal pull-up resistor pinMode(2, INPUT_PULLUP); pinMode(13, OUTPUT); } void...
2、数字输入上拉 DigitalInputPullup - 输出上拉串口 InputPullupSerial This example demonstrates the use of INPUT_PULLUP with pinMode(). It monitors the state of a switch by establishingserial communicationbetween your Arduino and your computer over USB. 本例演示如何使用 pinMode 和 INPUT_PULLUP。
1、输出(OUTPUT)模式 2、输入(INPUT)模式 3、输入上拉(INPUT_PULLUP)模式 (仅支持Arduino 1.0.1以后版本) 在输入上拉(INPUT_PULLUP)模式中,Arduino将开启引脚的内部上拉电阻,实现上拉输入功能。一旦将引脚设置为输入(INPUT)模式,Arduino内部上拉电阻将被禁用。 设置Arduino引脚为输出(OUTPUT)模式 当引脚设置为输...
This example code is in the public domain */ void setup() { //start serial connection Serial.begin(9600); //configure pin2 as an input and enable the internal pull-up resistor pinMode(2, INPUT_PULLUP); pinMode(13, OUTPUT); }
pinMode(button, INPUT); // Set initial rotation direction digitalWrite(in1, LOW); digitalWrite(in2, HIGH); } void loop() { int potValue = analogRead(A0); // Read potentiometer value int pwmOutput = map(potValue, 0, 1023, 0 , 255); // Map the potentiometer value from 0 to 255 ...
The parameters of the function of the function include:The minimum input (in this example is 0)，The input maximum value (in this example 1023)，The minimum output (in this example 0)，The output maximum value (in this example is 100).最后，我们使用`Serial.print()`函数将转换后的值打印到...
voidsetup(){//arduino程序设计基础的71页,在串口显示器上, //输入‘a’,13LED就打开,输入‘b’,13LED就关闭Serial.begin(9600);pinMode(13,OUTPUT);}voidloop(){if(Serial.available()>0){//判断串口缓存区是否有数据,有的话执行下面的程序char ch=Serial.read();Serial.print(ch);//开灯if(ch=='...
{delay(1000);lcd.begin(16,2);Serial.begin(9600);pinMode(enroll, INPUT_PULLUP);pinMode(up, INPUT_PULLUP);pinMode(down, INPUT_PULLUP);pinMode(del, INPUT_PULLUP);pinMode(match, INPUT_PULLUP);pinMode(buzzer, OUTPUT);pinMode(indFinger, OUTPUT);digitalWrite(buzzer, LOW);if(digitalRead(en...