这段代码用于读取连接在数字引脚2上的按钮(pushbutton)的状态,并将结果通过串行监视器(Serial Monitor)打印出来。 /* DigitalReadSerial Reads a digital input on pin 2, prints the result to the serial monitor This example code is in the public domain. */ // digital pin 2 has a pushbutton attached...
2、数字串口读取 - Digital Read Serial Read a switch, print the state out to the Arduino Serial Monitor. 读取开关状态,并打印状态到 Arduino 串口监视器。 This example shows you how to monitor the state of a switch by establishingserial communicationbetween your Arduino and your computer over USB....
Serial.println(sensorValue); 现在,当你打开Arduino IDE的串口监视器,你会看见“0”的数据流(如果开关打开)或者“1”的数据流(如果开关闭合) /* DigitalReadSerial Reads a digital input on pin 2, prints the result to the serial monitor This example code is in the public domain. */ // digital pin...
read(): 描述:读取传入的串行数据。 函数原型:Serial.read() 参数:无 返回值:可用的传入串行数据的第一个字节(如果没有可用的数据,则为-1) - int print(): 描述:在串行口以人们可以看懂的 ASSCII 码的形式打印数据。 函数原型:Serial.print(val) / Serial.print(val, format) 参数: val:要打印的值...
DigitalReadSerial- 读取一个按键, 并把它的状态输出到 Arduino 串口窗口 Fade- 示范使用模拟输出使 LED 变暗. ReadAnalogVoltage- 读取模拟输入,并把电压输出到 Arduino 串口窗口 翻译:硬创联盟翻译组翻译员 – Lepton-华 审核:硬创联盟翻译组技术审核 - 神奇海螺 ...
/*DigitalReadSerial Reads a digital input on pin 2, prints the result to the serial monitor This example code is in the public domain.*/intbuttonState =0;voidsetup() { pinMode(2, INPUT); Serial.begin(9600); }voidloop() {//read the input pinbuttonState = digitalRead(2);//print out...
格瑞图:Arduino-0002-内置示例-模拟读 Analog Read Serial 格瑞图:Arduino-0003-内置示例-最简化代码 Bare Minimum 格瑞图:Arduino-0004-内置示例-闪烁 Blink 格瑞图:Arduino-0005-内置示例-数字串口读取 Digital Read Serial 格瑞图:Arduino-0006-内置示例-亮度调节 Fade ...
3.read() 4.flush() 5.print() 6.println() 7.write() 8.peak() 9.serialEvent() 总结 前言 提示:以下是本篇文章正文内容 一、程序结构 在Arduino 中,标准的程序入口 main 函数在内部被定义, 用户只需要关心以下两个函数: loop() 和setup() ...
serial DigitalPins Blink Without Delay: 不用delay()函数,使LED灯闪烁 Button: 用一个按钮来控制LED灯 Debounce: 读取一个按钮,并滤掉噪音 Button State Change: 记录按键按下的次数 Input Pullup Serial: 示范怎么用pinMode()来上拉引脚 Tone: play 用压电扬声器弹奏一个旋律 ...
Serial.println("Button pressed!"); }// Remember last button press eventlastButtonPress = millis(); }// Put in a slight delay to help debounce the readingdelay(1); } 工作说明 要了解Arduino UNO的旋转编码器,请根据电路图连接电路或按照连接表进行连接。然后在Arduino IDE中编写上面给出的代码,并...