// read the input on analog pin 0: int sensorValue = analogRead(A0); // Convert the analog reading (which goes from 0 - 1023) to a voltage (0 - 5V): float voltage = sensorValue * (5.0 / 1023.0); // print out the value you read: Serial.println(voltage); } 代码功能 读取电位...
void loop() { // read the input on analog pin 0: int sensorValue =analogRead(A0); // Convert the analog reading (which goes from 0 - 1023) to a voltage (0 - 5V): float voltage = sensorValue * (5.0 / 1023.0); // print out the value you read: Serial.println(voltage); } 火...
2、读取模拟电压 - Read Analog Voltage Reads an analog input and prints the voltage to the Serial Monitor. 读取模拟输入并打印电压值到串口监视器。 This example shows you how to read an analog input on analog pin 0, convert the values from analogRead() into voltage, and print it out to the...
int analogvalue = analogRead(A0); temp = (analogvalue * 5.0) / 1024.0; // FORMULA USED TO CONVERT THE VOLTAGE input_volt = temp / (r2/(r1+r2)); 在这里,我们在Arduino的LCD和串行监视器上显示了测量的电压值。因此,在代码中,Serial.println用于在串行监视器上打印值,lcd.print用于在16x2 LCD上...
格瑞图:Arduino-0007-内置示例-读取模拟电压 Read Analog Voltage 格瑞图:Arduino-0008-内置示例-非延迟闪烁 Blink Without Delay 格瑞图:Arduino-0009-内置示例-按钮 Button 格瑞图:Arduino-0010-内置示例-去抖 Debounce 格瑞图:Arduino-0011-内置示例-数字输入上拉 DigitalInputPullup ...
思维导图Mind mapping在Arduino中，模拟输入通常指的是通过Arduino的模拟引脚读取来自传感器、按钮或其他模拟设备的电压值。Arduino板上有多个模拟引脚（通常标记为A0-A5），可以用来读取模拟信号。In Arduino, analog input usually refers to the voltage value from the sensor, buttons, or other analog device ...
Serial.println(voltage) 现在,当你打开你在Arduino IDE软件上的串口监视器(可以通过键盘快捷键Ctrl+Shift+M打开),你应该看到一个范围从0.0-5.0的稳定的数据流。随着你转动那个旋钮,这个输入到A0引脚的电压值会随之变化。 /* ReadAnalogVoltage Reads an analog input on pin 0, converts it to voltage, and pr...
/*ReadAnalogVoltage 读取模拟电压 Reads an analog input on pin 0, converts it to voltage, and prints the result to the serial monitor. OPEN THE SERIAL MONITOR TO VIEW THE OUTPUT >> Attach the center pin of a potentiometer to pin A0, and the outside pins to +5V and ground. ...
void setup(){ Serial.begin(115200); pinMode(PA0, INPUT_ANALOG);}void loop(){ delay(50); Serial.print("PA0="); Serial.println(analogRead(PA0));} 3）串口资源 总共3个硬件外接串口Serial1、Serial2、Serial3，一个USB虚拟串口Serial，测试代码示例：void setup(){ Serial.begin(115200...
登录后复制Serial.print(" analog input ") ;// this gives name which is “analog input” to the printed analog valueSerial.print(m);// this simply prints the input analog value 代码中指定的所需交流电压: 登录后复制Serial.print(" ac voltage ") ;// this gives name “ac voltage” to the...