1)ADC valueADC值 1.DWI signal and ADC value were evaluated in cerebritis stage, capsule formation stage, and evolution stage of brain abscess and compared with those of cys.目的:研究DWI及ADC值在鉴别脑脓肿与坏死囊变脑转移瘤中的应用价值。 2.Objective To apply MR diffusion weighted imaging to...
假设你你的ADC_value[2000]，如果DMA工作于单次方式，那么装满2000个数据后DMA就停止工作了，除非你重置DMA的CNDTR寄存器。如果工作于循环方式，DMA在填充ADC_value[1999]后，又回到ADC_value[0]重新开始填充，周而复始。
网络表观弥散系数值 网络释义 1. 表观弥散系数值 目的:探讨前列腺癌(Pca)的表观弥散系数值(ADC-value)与前列腺癌Gleason评分、临床分期及PSA的相关性.方法:分析经穿刺活 … d.wanfangdata.com.cn|基于 1 个网页 释义: 全部,表观弥散系数值
I have seen a few post regarding ADC reads keep returning 4081 instead of 4095, and in my test I realize that at about 3.3V/2=1.65V, the value I read is always 4081. I tried ADC CH1,2,3,4 all returned the same result... 4081 from 1.6V onwards. Why so weird? Other opened ...
I have seen a few post regarding ADC reads keep returning 4081 instead of 4095, and in my test I realize that at about 3.3V/2=1.65V, the value I read is always 4081. I tried ADC CH1,2,3,4 all returned the same result... 4081 from 1.6V onwards. Why so weird? Other opened ...
I have seen a few post regarding ADC reads keep returning 4081 instead of 4095, and in my test I realize that at about 3.3V/2=1.65V, the value I read is always 4081. I tried ADC CH1,2,3,4 all returned the same result... 4081 from 1.6V onwards. ...
1.Connect power from power supply to adc pin2.Read caluated adc value. results are as below.(Input / caled value)1.001V / 10181.101V /11251.201V /12241.5V /15312.001V /20472.501V /25613.001V /30753.501V /35944.001V /41034.500V /46264.800V /49255.000V /5000 The difference is growi...
adc_getinjectedconversionvalue 是STM32 标准外设库中的一个函数,用于从 ADC 注入通道的转换结果寄存器中读取转换后的数字值。 2. adc_getinjectedconversionvalue 函数的作用 该函数的主要作用是读取指定 ADC 注入通道的转换结果。在 STM32 的 ADC 模块中,注入通道可以在规则通道转换过程中被中断,用于执行紧急或高...
Hi there, I am using PICO2206A. I am collecting of DATA using PicoScope2000aGetBlock.vi and return as ADC value. I would like to have voltage value and how to do it? In addition, I would like time base to be 400 ms, what is value to apply? Many Thanks. Walter....
It did however change the ADC value's shift-point to 1.7KΩ off-board resistance. --- SETUP #3I noticed this in the datasheet, so i tried making VDDA_ADC_3P3 = 3.3V (I assume this is VDDA?), but this still did not correct the ADC shift behavior. --- SETUP #4Leaving R14 as...