Read ADC data values from ADC Interface block expand all in page Library: SoC Blockset / Processor I/O Description TheADC Readblock converts the message received from theADC Interfaceblock to a signal that can be used by an algorithm. The data type of the output signal is the same as the...
*函数名 : xpt2046_read_data * 函数功能 : XPT2046读数据 *输 入 : 无 *输 出 : XPT2046返回12位数据 ***/ u16 xpt2046_read_data(void) { u8 i; u16 dat=0; CLK = 0; _nop_(); for(i=0;i<12;i++)//循环12次,每次读取一位,大于一个字节数,所以返回值类型是u16 { dat <<= 1;...
我们不能通过I²C直接读取所有数据ALSDATA[13:0],需要首先读取寄存器0x04的内容,然后读取寄存器0x05的内容,再把这些数据合并到一个至少16位的寄存器内。因此,在读取这些数据时需要特别谨慎。通过两次简单的单字节读操作(利用STOP (P)条件终止)完成数据读取,如图1所示。 图1. 单字节读操作 这种方法存在致命缺陷,...
#defineCS_ADC_LOW()GPIO_ResetBits(GPIOA,GPIO_Pin_4)#defineCS_ADC_HIGH()GPIO_SetBits(GPIOA,GPIO_Pin_4)voidSPI1_Init(void);u8SPIx_ReadWriteByte(u8 TxData);#endif 3.1.3 SPI.C代码 代码语言:javascript 代码运行次数:0 运行 AI代码解释 #include"spi.h"#include"delay.h"/* 复用功能 SPI1_...
读取作为 read 命令执行,后跟 null 命令以收集返回帧的第一个字中的响应。 问题- 数据表中不清楚登记的厚度是否需要对单调信号的地址。 这是必要的,或者您可以随时访问注册表。 认识到五分之三将不同步。 如果在下一个单调的脉冲之前没有读取第五次再同步问题,则响应(对于单个寄存器访问)是否会...
Bit 5 RXNE: Read data register not emptyThis bit is set by hardware when the content of the RDR shift register has been transferred tothe USART_DR register. An interrupt is generated if RXNEIE=1 in the USART_CR1 register.It is cleared by a read to the USART_DR register. The RXNE ...
*function name: unsigned long AD_read(void) *description : read AD data *input : null *output : null *return £ºnull ***/ unsigned long AD_read(unsigned char channel) { int i=0; unsigned long ad_value=0; AD_InitIO(); SCLK_L; PDWN_L; ...
return sizeof(adc_data); } /* (1) adc_read函数中,ssize_t是表示读写数据块的大小,类型是无符号整形 * (2) (1<<14) 预分频使能,(255<<6)预分频值设为255,(0<<3)模拟输入通道AIN0 * (1<<0)使能AD转换,依据开发板启动信息(S3C244X:core 405 MHZ 等)能够知道开 ...
Ginkgo2有16路ADC,单路ADC采样率可达1M,Ginkgo2USB数据传输速度可达600KBye/s,所以完全有能力将数据快速的上传到上位机,Ginkgo2ADC主要用到ADC_Init()和ADC_ReadData()两个函数即可,调用方式很简单。上位机程序采用CVI来实现,CVI是NI专门基于测试测量出的一套类似于LABVIEW的库,不过这个库全部是C语言封装的,所以...
inserted_data[3] = adc_inserted_data_read(ADC0, ADC_INSERTED_CHANNEL_3); } 6.5.ADC 使用注意事项 ADC通道的采集引脚未配置为模拟输入,GD32要求通道IO口必须配置为模拟输入; ADC时钟过高,ADC采样时钟高于ADC最高采样时钟获取到的数据不具有参考意义,需要手动分频到合适的ADC 要求的频率; ...