Temperature (ISO 11403-2) 物理性能 额定值 单位制 测试方法 比重 1.04 g/cm3 ASTM D792 熔流率(熔体流动速率)(220°C/10.0 kg) 23 g/10 min ASTM D1238 收缩率 -流动(3.20 mm) 0.40 到0.70 % ASTM D955 Dimensional Stability 0.0 % ASTM D1042 物理性能 额定值 单位制 测试方法 比重 1.04 g/...
Temperature℃ASTM D-648 (ISO 75/A)Unannealed 18.6kg/cm2 ( 1/2'' 厚 ) 91 熔融指數 Melt Flow Indexg/10 minASTM D-1238 ( ISO1133 )200℃×5Kg ( 49N ) - 220℃×10Kg ( 98N ) 3.5 比重 Specific Gravity ASTM D-792 ( ISO1183 )23℃/23℃ ...
Specific Volume vs Temperature (ISO 11403-2) 苯领PA/ABS 德国巴斯夫S NM-31 BASF 苯领PA/ABS 德国巴斯夫 N3154 BASF PA/ABS 德国巴斯夫 N3158 BASF PA/ABS 德国巴斯夫 N NG-02 BASF PA/ABS 德国巴斯夫 N NG-06 BASF PA/ABS 德国巴斯夫 NM-13 BASF 苯领PA/ABS 德国巴斯夫 NM-19 BASF PA/ABS 德国...
Single crystals of NaCl were compressed at room temperature. The stress-strain curve shows three well-defined stages similar to those found for fcc. metals. The dislocation density, bulk density, and deformation characteristics were stud...
The ABS polymers prepared by grafting contain varying amounts of ungrafted polybutadiene (which has a low glass transition temperature) and therefore have good low-temperature impact strength. Also, the ABS polymers prepared by grafting are superior to those obtained by blending in that moulded spec...
HeatDeflectionTemperature(0.45MPa,Annealed,4.00mm) ISO75-2/B 94.0 °C 载荷下热变形温度(1.8MPa,未退火,6.40mm) ASTMD648 93.0 °C HeatDeflectionTemperature(1.8MPa,Unannealed,4.00mm) ISO75-2/A 75.0 °C HeatDeflectionTemperature(1.8MPa,Annealed,4.00mm) ISO75-2/A 92.0 °C 维卡软化温度 -- IS...
The thermal degradation of acrylonitrile-butadiene-styrene copolymer (ABS-Br; 10 g) containing brominated flame retardant (Br: 9.59 wt.%) was carried out at 450℃ using a semi batch operation using two different temperature programs. The heating rate was found to affect the quality of the degra...
R R***n Oct 3, 2024 A very well designed and nice component. Very happy. China Explosion-Proof Pressure Transmitter with Digital Display A A***o Sep 25, 2024 Good product, good quality. service support. But will need an improvement on the device manual. Reviews with 1 repeated cont...
19.0J/cm2@Temperature 23.0 °C 90.4ft-lb/in2@Temperature 73.4 °F ISO 179 ABS NOVODUR HH-106 成型性能 无定形材料,流动性中等,吸湿大,必须充分干燥,表面要求光泽的塑件须长时间预热干燥80-90度,3小时; 宜取高料温,高模温,但料温过高易分解(分解温度为270度).对精度较高的塑件,模温宜取50-60度...
ABS【2020】 RULES FOR NONDESTRUCTIVE INSPECTION 无损检测指南.pdf,G u i d e f o r N o n d e s t r u c t i v e I n s p e c t i o n GUIDE FOR NONDESTRUCTIVE INSPECTION SEPTEMBER 2020 American Bureau of Shipping Incorporated by Act of Legislature of the Sta