1. ZYNQ fsbl阶段的调试方法(12447) 2. 使用axi_datamover完成ZYNQ片内PS与PL间的数据传输(7465) 3. ZYNQ 的PS GEM DMA存在缺陷(1387) 4. Tesla P4 在深度学习上的性价比辗压目前所有量产的FPGA(1374) 评论排行榜 1. Tesla P4 在深度学习上的性价比辗压目前所有量产的FPGA(2) 推荐...
systemctl restart network---(重启网卡) 到目前为止, 上面配置的网卡信息也只能ping通内网,ping不通外网, 上不了网。 获取设置具体IP、子网掩码、网关地址说明: 设置这3个参数你要知道你当前所处的网络环境, 比如公司内网, 家庭局域网, 餐厅, 咖啡厅等, 知道它们的网段,子网及网关, 就比如说我在家里上网有...
本主答复记录列出了 MPSoC 器件 PS 中千兆位以太网 MAC (GEM) 控制器的所有已知问题。 Solution 概述 在Zynq MPSOC 器件上,我们在 PS 中提供了 4 个 GEM,GEM 可为以太网通信节省 PL 资源,因此日益受到客户的欢迎和采用。 我们针对该硬 IP 提供了 MACB Linux 驱动程序和 EMACPS 独立驱动程序。
本主答复记录列出了 MPSoC 器件 PS 中千兆位以太网 MAC (GEM) 控制器的所有已知问题。 Solution 概述 在Zynq MPSOC 器件上,我们在 PS 中提供了 4 个 GEM,GEM 可为以太网通信节省 PL 资源,因此日益受到客户的欢迎和采用。 我们针对该硬 IP 提供了 MACB Linux 驱动程序和 EMACPS 独立驱动程序。
使用iperf对zynq进行单socket tcp传输速率测试; 无网络损伤时,单向网络带宽约为600Mbps,双向网络带宽相加约400Mbps; 50ms延时,1ms抖动,无丢包时,单向网络带宽约为155Mbps,双向网络带宽相加约40Mbps; 和内核版本无关,经技术支持确定为PS GEM DMA的双向传输存在缺陷。
Do you need to run Ethernet applications on a Zynq MPSoC device and consider using a Gigabit Ethernet MAC (GEM) core in the PS rather than using the PL logic? If so, this blog entry will provide guidance and some debugging tips which might help you design with the GEM core. Basics Th...
73065 - Zynq-7000 PS GEM Bidirectional Performance Description This answer record summarizes the bi-directional performance of the PS GEM on the Zynq-7000 device. The measurements are obtained on an Ubuntu 16.04 LTS high-performance host machine. Performance is expected to differ when a different...
65369 - 2015.2 - QEMU - How can I use two GEM on Zynq in QEMU Description My Zynq-7000 SoC system uses two Ethernet interfaces. Is it possible to use both interfaces in the QEMU environment? Solution Yes, this is possible. Follow the steps below to set this configuration up. ...
71168 - Zynq UltraScale+ MPSoC - PS GEM Flow Control limitation Description This article describes the Zynq UltraScale+ MPSoC PS GEM Flow Control limitation, its effects, and mitigation. Solution What is the limitation about? The PS GEM (Gigabit Ethernet MAC) has a hardware restriction where th...
第一步:调通PS侧网口GEM0(Xilinx BSP默认配好)。 第二步:调通PS侧网口GEM1(本文阐述)。 第三步:调通PL侧网口。 第四步:在PL侧网口上验证Jumbo Frame特性,并在应用层适配gigE Vision协议。 3. 预备知识 (1) 熟悉ZYNQ网口硬件资源 阅读《xapp1082 - PS and PL Ethernet Performance and Jumbo Frame Suppo...