Code This branch is up to date with jiangjiali66/zynq_examples:master.Folders and files Latest commit jjl format makeallclean.sh 8dfc7b2· Sep 23, 2015 History53 Commits devicetree 更新ds18b20在用户空间操作demo Sep 1, 2015 hardware_pro/workshop_v1_0 更新硬件工程约束 Aug 30, 2015 linux_...
3.共享外设中断(SPI) 共享中断就是 PL 的中断可以发送给 PS 处理。有 16 个 PL 的中断,它们可以设置为高电平或者低电平触发。中断控制器用于管理中断的优先级和接收用于 CPU 的这些中断。默认情况下,所有共享外设中断的复位是一个活动高电平。然而软件使用 ICDICFR2 和 ICDICFR5 寄存器将中断32、33和92编程为...
对于ZYNQ,有多种启动方式,比如从JTAG启动、从QSPI(即Flash)启动,从SD卡启动等。对于从JTAG启动的,我们直接运行程序就OK了。对于从Flash和SD卡启动的,需要我们生成这两种情况下对应的文件,并烧到对应的位置才可以。那么下面就介绍一下如何生成以及烧录。 生成FSBL FSBL的全称是First Stage Boot Loader,他是启动ZYNQ...
you seem to have removed the DDR in your design. I'm not sure why the FSBL absolutely requires the DDR, but I guess without external memory, and only the internal cache, you won't run far with a Cortex A9 processor.
可以看到部分 PL 到 PS 部分的中断,经过中断控制分配器(ICD),同时进入CPU1 和 CPU0。查询下面表格,可以看到 PL 到 PS 部分一共有 20 个中断可以使用。4 个快速中断(PPI),即IRQF2P[19:16];16 个共享中断(SPI),即 IRQF2P[7:0]、IRQF2P[15:8]。这 16 个中断可以任意定义......
xdmaps_example_w_intr_14_2.c Snippet of code. Block Diagram Solution Overview In order to achieve Linear Mode Maximum Effective Throughput with 100 MHz SPI clock, the DMA controller has been used. This very flexible DMA can execute a few lines of microcode in order to transfer data from ...
SPI:shared peripheral interrupt,共享外设中断,该中断来源于外设,可以对所有的core有效。 SGI:software-generated interrupt,软中断,软件产生的中断,用于给指定的core发送中断信号 控制器功能框图如下: 上图中, ICD的控制寄存器主要如下: 1)APU GIC,功能框图如下 ...
ZYNQ_QSPI_FLASH烧写教程 注意:烧写之前先保证程序在JTAG方式在线仿真没有问题。 1. 在BLOCK上的ZYNQ system的MIO Configure添加Quad SPI Flash部分,注意一定要勾选Feedback clk; 2. Clock configure 中的设置Q...10个常见的Node.js面试题 如果你希望找一份有关Node.js的工作,但又不知道从哪里入手评测自己...
Quad-SPI Interface Drive Strength MIO Table at a Glance Register Overview Programming Model I2C Interface Programming Example PS-GTR Transceivers Introduction Features Functionality Clocking Power PCIe v2.0 PHY Protocol USB3.0 PHY Protocol DisplayPort 1.2a PHY Protocol (Transmitter only...
1 /*number of bytes per SPI word*/ }; DSP can send data to ZYNQ. Code as below: /*Since SPI TX and RX shares same clock and control signals, SPI TX and RX actually happens at the same time even you only want to TX or RX. But, ...