zynq zc706 JTAG调试、QSPI FLASH 程序固化及遇到的问题 配置Run Configurations 如下 二、生成BOOT.mcs文件1.在vivado中生成比特流文件2.在SDK中通过JTAG在线调试,调试好后将程序烧写到FLASH中a.设置现在...qspi_dual_parallel(2018.3选qspi_x8_dual_parallel),如果为默认的qspi_single 可以完成烧写,但是INIT灯变为...
FSBL.elfbit文件XXX.elf一定按顺序添加 三、将BOOT.mcs文件固化到FLASH 在JTAG启动模式下点击Program Flash 注意 :zc706 Flash Type 选取qspi_dual_parallel(2018.3选qspi_x8_dual_parallel),如果为默认的qspi_single 可以完成烧写,但是INIT灯变为红色,且DONE灯不亮 没有完成BIT文件 ...
(4)QSPI固化(Dual Quad SPI Parallel 8 bit模式)。 ZC706中,MAC 控制器与 PHY 通过 RGMII(Reduced Gigabit Media Independent Interface)接口进行连接,实现千兆网。 一、工程概述 1. 开发板配置 使用Xilinx ZYNQ开发板ZC706,默认配置ARM后即可使用PS端网口、串口和QSPI,放置AXI GPIO的IP核驱动PL端的4个LED。 A...
* (Used in dual parallel configuration) */ struct zynq_qspi { struct device *dev; @@ -141,6 +148,8 @@ struct zynq_qspi { int tx_bytes; int rx_bytes; struct completion data_completion; u32 is_dual; bool is_stripe; };/*
68476 - Zynq UltraScale+ MPSoC - 2016.3 u-boot - cannot probe Spansion QSPI flash in dual parallel mode Description In my Zynq MPSoC board, there are two QSPI flash (Spansion flash: S25FL512SAGMFI011) in dual parallel mode.In JTAG mode, 2016.3 SDK can program QSPI flash correctly.However...
Under the described condition, the QSPI controller in dual parallel mode can fail an operation on the lower memory when a prior write operation to the lower memory takes longer than the upper memory. Work-around: Set Manual_CS to manual mode instead of auto mode or use a BAUD_RATE_DIV ...
QSPI24 and QSPI32 The QSPI boot mode supports the following: • x1, x2, and x4 read modes for single Quad SPI flash memory (QSPI24) and x8 for dual QSPI • Image search for MultiBoot • I/O mode is not supported in FSBL Note: Single Quad-SPI memory (x1, x2 and x4) is ...
- Select **qspi-x8-dual_parallel** as the Flash type. - Set the Offset as 0 and select the BOOT.bin file. - Click Program to start the process of programming the QSPI flash with the BOOT.bin. - Wait until you see the message “Flash Operation Successful” in the console.Set...
QSPI ISSI is25l is25lp01g 1024 x1-dual_stacked, x1-single, x2-dual_stacked, x2-single, x4-dual_stacked, x4-single, x8-dual_parallel QSPI ISSI is25lp is25lp016d 16 x1-dual_stacked, x1-single, x2-dual_stacked, x2-single, x4-dual_stacked, x4-single, x8-dual_parallel QSPI ISSI ...
1. We have 2x 512Mbit (Mb) QSPI (Micron MT25QU512) in dual parallel mode (x8) for a total of 128MBytes (MB) 2. We are booting in QSPI32 mode I have read the following AR and UGs: - AR_65463 in which is written that the QSPI boot image search limit ...