4.6.1 上电复位(PS_POR_B) Zynq PS部分支持上电复位,此复位会复位整个芯片,此复位信号接到外部电源管理。 4.6.2 PL复位(PROG_B ) 这部分是FPGA部分的逻辑资源复位,此管脚接到MiZ701核心板上SW1脚 4.6.3处理器子复位 此复位信号可以手动复位系统,包括PL部分。此管脚寄到MiZ701核心板上SW2脚 4.7用户IO ...
The BootROM controls the logic level on the INIT_B pin indirectly by writing to the devcfg.CTRL[PCFG_PROG_B] bit. In 7z020/45 CES devices, the INIT_B pin does not indicate a PS boot failure. Impact: Trivial. Work-around: None. Configurations Affected: All. Device Revision(s) Affect...
b) In Vivado Hardware Manager, select a lower cable frequency and re-attempt configuration. c) Pulse the PS_PROG_B push button on the ZCU102 (SW5). Pulsing PROG will clear out any problems caused by power up ramp rate issues to the FPGA. d) Review(Xilinx Answer 34904)- Xilinx Configur...
Styx配置下载工具目前不支持通过JTAG编程FPGA SRAM。 有关为FT2232H信道B选择SPI或JTAG的信息,请参阅下表。必须选择SPI才能使Styx配置下载实用程序工作。 Solder Jumpers P2 重要提示:这些跳线设置仅用于使用xc3sprog等程序通过FT2232H通过USB访问JTAG信号。如果JTXILINX没有连接到外部的USB接口,请不要更换。它们应该...
当FT2232H信道B连接到FPGA JTAG时,JTAG信号可以通过FT2232H直接访问。Styx配置下载工具目前不支持通过JTAG编程FPGA SRAM。 有关为FT2232H信道B选择SPI或JTAG的信息,请参阅下表。必须选择SPI才能使Styx配置下载实用程序工作。 Solder Jumpers P2 重要提示:这些跳线设置仅用于使用xc3sprog等程序通过FT2232H通过USB访问...
dpll_prog is available in some psu_init files that's why this function should stay there. Signed-off-by: Michal Simek <michal.simek@xilinx.com>master v2021.07-rc2 … v2020.01-rc1 Michal Simek committed Oct 24, 2019 1 parent c126ba4 commit d8a6d1b Showing...
zynq7020_v1.2
b) In Vivado Hardware Manager, select a lower cable frequency and re-attempt configuration. c) Pulse the PS_PROG_B push button on the ZCU102 (SW5). Pulsing PROG will clear out any problems caused by power up ramp rate issues to the FPGA. ...
当FT2232H信道B连接到FPGA JTAG时,JTAG信号可以通过FT2232H直接访问。Styx配置下载工具目前不支持通过JTAG编程FPGA SRAM。 有关为FT2232H信道B选择SPI或JTAG的信息,请参阅下表。必须选择SPI才能使Styx配置下载实用程序工作。 Solder Jumpers P2 重要提示:这些跳线设置仅用于使用xc3sprog等程序通过FT2232H通过USB访问...