## Error:flags type check failurefor"serverip"<="AUTO"(type:i)himport_r:can't insert"serverip=AUTO"into hash tableIn:serialOut:serialErr:serialNet:ZYNQGEM:e000b000,phyaddr ffffffff,interfacergmii-idPHYis not detectedGEMPHYinit failed No ethernet found.U-BOOTforh1_petalinux_testZYNQGEM:e0...
rc= f_open(&fil, file_name, FA_OPEN_ALWAYS | FA_WRITE); if (rc) { "SD: Unable to Write File %s\n", file_name); return XST_FAILURE; } fsize); if (rc) { "Shift Pointer To the End of File Failed \r\n"); return XST_FAILURE; } rc= f_write(&fil,(void*)SourceAddress,L...
int fd = open("/dev/my_adc_axi_dma", O_RDWR); struct dma_ioctl_args args; unsigned char *user_buffer; args.rx_buf_size = 1024 * 1024; args.package_length = 200; args.package_number = 1; args.dst_addr = 0; if (fd < 0) { perror("Failed to open device"); return EXIT_F...
if (Status != XST_SUCCESS) { xil_printf("SD Polled File System Example Test failed \r\n"); return XST_FAILURE; } xil_printf("Successfully ran SD Polled File System Example Test \r\n"); return XST_SUCCESS; } int FfsSdPolledExample(void) { FRESULT Res; UINT NumBytesRead; UINT NumB...
最近某平台又大量出现了Zynq7010的板子,据说是某通讯基站上的设备,于是花15一块卖了几块来玩玩,分享下玩板过程。 二.板载资源分析 网上没有搜索到对应的板子资料,于是就对着PCB线分析下。 板子的成色是不错的,器件都很新,除了暴力拆解有一些电阻电容掉了,边角掰断了,其他都还不错,就算拆器件也能挣回成本。
大多数 SDR 设计都有 3 个不同的内部运行频率:一个低基带频率,用于处理来自 ADC/DAC 的数据;一个或多个中间频率,最终基带数据流作为中间步骤提升到该频率;以及最终的 RF 将输入/输出天线的输出频率。显然,最简单的起点是基带,因为它是最低频率,并且是实际模拟数据流从各个数字数据位组合在一起/提取的地方。为...
f_open(&fil,file_name,FILE_NAME); //移动打开的文件对象的文件读/写指针 0:指向文件开头 f_lseek(&fil,0); //从SD卡中读出数据 f_read(&fil,(void*)src_addr,byte_len,&br); //关闭文件 f_close(&fil); return 0; } //SD卡写数据 ...
43 printf("ERROR: %s file openfailed!\n", argv[1); 44 return -1; 45} 46 47 /* 循环读取按键 */ 48 for ( ; ; ){ 49 50read(fd, &key_val, of(int)); 51 if (0 == key_val 52 printf("KeyPress\n"); 53 else if (1 == key_val) 54 printf...
pmu@f8891000 { compatible = "arm,cortex-a9-pmu"; interrupts = <0x0 0x5 0x4 0x0 0x6 0x4>; interrupt-parent = <0x4>; reg = <0xf8891000 0x1000 0xf8893000 0x1000>; }; fixedregulator { compatible = "regulator-fixed"; regulator-name = "VCCPINT"; ...
xil_printf("XAXIDMA_DMA_TO_DEVICE transfer failed... "); return XST_FAILURE; } cleanup_platform(); return 0; } 测试设备 为了验证模拟输出,将其通道 1 连接到示波器通道 1,并在主机 PC 上启动 WaveForms 来查看它。 然后,在 Vitis 中启动 C 应用程序的调试,并在 MM2S 传输开始之前设置了断点: ...