The printer status is not good 〔 无法Ready〕,Error 灯闪烁, 因为无纸、 无色带等; The status is not ready, Error light blink due to out of paper, out of ribbon; 因为无存储空间 Because of no memory space 重新校准; Do the calibration again; 检查、调整测纸、 测色带、 测打印头温度、打印...
The printer status is not good (无法Ready〕,Error灯闪烁,因为无纸、无色带等; The status is not ready, Error light blink due to out of paper, out of ribbon; 因为无存储空间 Because of no memory space 重新校准; Do the calibration again; 检查、调整测纸、测色带、测打印头温度、打印头开合等传...
This articles discusses the Error Condition Paper Out on Zebra printers. The error, Error Condition Paper Out can have several causes. No label stock is loaded into the printer Label stock is not loaded properly and is not aligned with the ...
3)在“Command to send to printer”输入“! CSA 0”,然后单击“Execute”按钮 等一会儿直到“Printer Status”栏里显示2组数字还有一个确认信息,类似以下: Y:xx B:yy .这里xx和yy数字不重要,但是你必须看到ACK。 4)安装一个新的YMCKO彩色带或者确认正常的YMCKO彩色带,合上打印头。 5)在“Command to send...
status :STRING PRINTER_STATUS_SUCCESS, PRINTER_STATUS_ERROR. message :STRINGOptional Error message, only if status = ERROR. propertyWithIntValue :INTEGEROptional Currently unused. Returns Synchronous Return: Void Platforms Android Windows Mobile
3) 在“Command to send to printer” 输入 “! CSA 0” ,然后单击“Execute” 按钮 等一会儿直到 “Printer Status”栏里显示2组数字还有一个确认信息,类似以下: Y:xx B:yy . 这里 xx 和 yy 数字不重要,但是你必须看到 ACK. 4) 安装一个 新的YMCKO 彩色带或者确认正常的YMCKO彩色带,合上打印头。
5.我们 105SE 原可打印中文,后BAR-ONE程序不幸卸载,重装后就不能打印中文了,请指教如何设置.谢谢 答:安装完后修改:BIN下SETUP.INI 文件 {printer1} ;TTFSizeThreshold=1去掉分号,在其下加以下一行 “TTFROTATETHRESHOLD=1” ... 6.我有一台ZBERA140XI的打印机出现一开机错误指示灯亮屏幕显示:ERROR CONDITION...
The status indicator (see Figure 3, Printer Exterior, Rear View, on page 9) has several functions: ON constantly The printer is operational. Flashes rapidly Indicates error. Hold down the feed-forward button and the number of flashes will reflect the status-code. See Table 1. Flash, pauses...
The printer adds an error code in the status report (error, top of form, byte 1, bit 3) if no black-mark is found within the specified distance. ESC x n1 n2 1B 78 n1 n2 hex Delay cut after black mark detection 027 120 n1 n2 decimal n1n2 Sets the number of 0.125-mm steps to...
Printer.searchPrinters({ connectionType:EB.Printer.CONNECTION_TYPE_USB, printerType: EB.Printer.PRINTER_TYPE_ZEBRA }, function (cb){ if(cb.status == 'PRINTER_STATUS_SUCCESS') { if (typeof cb.printerID != "undefined") { console.log('Found: ' + cb.printerID) // > Found ZEBRA_PRINTER...