网络释义 1. 轴长度计算 Z轴长度计算(Z-Axis delay) „ 在15.2 版本中, 康世权经理更准确的计算钻孔长度, 将钻孔长度造成的时间延迟也一倂考虑,其设定... www.elecfans.com|基于3个网页
Measure from true signal origin to end point through vias and through packages, not just the etch, so you can get timing right and ensure signal performance.
For i = 0 To gv_MaxAxisNum - 1AXIS_ENABLE(i) = 0 '关闭轴使能atype(i) = 0 '设置为虚拟轴类型AXIS_ADDRESS(i) = 0 '清零轴地址信息NEXT i'等待片刻，以确保所有驱动器都有足够的时间进行状态切换。DELAY(10) '延迟10毫秒，防止瞬间电流过大。'接下来，停止当前正在使用的总线槽位，并等待片刻以...
delay(300)'延时300ms'判断扩展板的连接状态'CanID 1 ZIO1632 in(32)~in(47),op(32)~op(63)'CanID3ZIO16082 in(64)~in(79),op(64)~op(71),axis*2'CanID 4 ZAIO0802 ain(40)~ain(47),aout(20)~aout(21)IF CANIO_STATUS(1)=1 AND CANIO_STATUS(3)=1 AND CANIO_STATUS(4)=1 THEN '...
{ int16_t z_axis = readAxisData(0x18); // 假设 Z 轴数据寄存器为 0x18 Serial.print("Z轴数据: "); Serial.println(z_axis); delay(100);}int16_t readAxisData(uint8_t reg) { Wire.beginTransmission(QMA6100P_ADDR); Wire.write(reg); Wire.endTransmission(); Wire.requestFrom(QMA6100P...
IO映射采用扩展模块上自带的拨码开关设置,轴映射采用AXIS_ADDRESS指令映射轴号。 拨码开关意义: ZCAN扩展模块一般带8位拨码开关,拨ON生效,如图所示: 拨码含义如下: 1-4:4位CAN ID用于ZCAN扩展模块IO地址映射,对应值0-15。 5-6:CAN通讯速度,对应值0-3,可选四种不同的速度。
Z-Axis Calibration: The plugin performs Z+ homing to ensure proper Z-axis alignment before resumption. State Restoration: The plugin restores temperatures, fan speeds, and positional data. Print Continuation: The printer resumes printing from the last saved state. Configuration Guide Basic Setup Add...
y axis y 轴y circuit 星形连接y position y位置y punch y穿孔位y signal y信号y type address constant y 型地址常量y wire 纵向线yagi antenna 八木天线yes no code 是否代码yes no decision 是否决策yes no question 是否问题yield 成品率yield curve 成品率曲线yoke 偏传线圈z type constant z型常数zener...
(1) and the tool electrode when the tool electrode is contacted with the tool setting block, the Z-axis moves continually for pressing the buffer spring (8) due to delay of a signal in transmitting and acquiring processes till the machine tool sends a command and the Z-axis stops moving,...
6040Z 800W 4axis Size:Parallel Port Parallel Port USB Port Reviews Due to our system upgrades, this content is currently unavailable in your region. Related items Specifications Hign-concerned Chemical None Controller MACH3 Is Smart Device