但是偶尔会出现无法自动从Flash加载的情况。只能手动点击“Boot from Configuration Memory Device” 目前的找不到原因。不过有个方案,也许可能解决这个问题。就是打开GUI界面,将FPGA配置参数按板卡的情况正确设置,工具会自动将需要的约束全部添加到Xdc中。当这些参数都添加到Xdc中之后,有很大的概率,会让这个问题消失。所以,如果遇到这个问题,不放将相关的配置参数都添加完善,然后...
3、烧写完成后选择Boot from Configuration Memory Devive去加载FPGA。 4、在FPGA加载后可以看到板卡上面LED2灯点亮。 5、在Hardware Device Properties的BOOT_STATUS里面可以看到INTERNAL_PROG使能;由于加载没有错误,目前运行的是Multiboot程序。CONFIG_SATUS里面可以看到DON_PIN拉高。 下面我们尝试把multiboot image里面的...
3、烧写完成后选择Boot from Configuration Memory Devive去加载FPGA。 4、在FPGA加载后可以看到板卡上面LED2灯点亮。 5、在Hardware Device Properties的BOOT_STATUS里面可以看到INTERNAL_PROG使能;由于加载没有错误,目前运行的是Multiboot程序。CONFIG_SATUS里面可以看到DON_PIN拉高。 下面我们尝试把multiboot image里面的...
The boot image must be located within the first 128 MB address space of the NAND flash device for the BootROM Header search function. The BootROM reads the ONFI compliant parameter information in 8-bit mode to determine the device width. If the device is 16 bits wide, then the BootROM e...
In all configuration modes except SPI mode, RS[1:0] is controllable by WBSTAR. 在P119中讲到了WBSTAR相关的内容,也涉及到了RS[1:0],具体如下所示: The warm boot start address register (WBSTAR) specifies the MultiBoot address location to be used when the IPROG command is applied. The name...
(XAPP1246) MultiBoot with 7 Series FPGAs and BPI (XAPP1239) Using Encryption to Secure a 7 Series FPGA Bitstream (XAPP1232) Bitstream Identification with USR_ACCESS using the Vivado Design Suite (XAPP1188) FPGA Configuration from SPI Flash Memory using a Microprocessor (XAPP1179) Using Tand...
KR260首先从QSPI加载BOOT.BIN启动U-BOOT,U-BOOT再从SD(TF)卡的第1个分区(sda1)启动Linux内核,Linux内核再把SD(TF)卡的第2个分区(sda2)加载为根文件系统。BOOT.BIN包含FSBL、U-BOOT。Linux的启动文件包括boot.scr,Image,ramdisk.cpio.gz.u-boot,system.dtb,system-zynqmp-sck-kr-g-revB.dtb等。
答:First Stage Bootloader 一般保存在 Boot Memory (可以试 SD 卡,QSPI Flash, NAND ,NOR Flash),在 Zynq 上电之后,Zynq 内部固化的 BootROM 执行之后, 会从 Boot Memory 中读取 First stage Bootloader Q9:请问开发用的软件是免费提供的吗? 答:有免费的版本 Q10:您好,7020 由于管脚复用问题,无法同时支持 ...
u-boot Configuration ---> (0x11000000) netboot offset kernel配置: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 petalinux-config -c kernel #手动配置 [*] Enable loadable module support ---> Device Drivers ---> Generic Driver Options ---> ...
図 11. TPS54308 Functional Block Diagram EN IN Ip Ih Thermal Hiccup UVLO Overvoltage Comparator Enable Comparator Shutdown Logic Hiccup Shutdown + Error FB Amplifier + + Voltage Reference HS MOSFET 20 k Current Comparator Boot Charge Boot UVLO Current Sense Soft Start 2 pF 2.04 nF Power Stage...