多串口系统设计时需要注意AXI总线基地址(XPAR_UARTNS550_x_BASEADDR)和设备编码(XPAR_UARTNS550_x_DEVICE_ID)与16550模块编号并非顺序对应,在使用时注意做地址转化。 Vivado Block Design Block Design AXI CLK Frequency:250MHz XDC文件 set_property PACKAGE_PIN N17[get_ports sin_0]set_property PACKAGE_PIN...
LogiCORE IP AXI UART 16550 (v1.01a) DS748 July 25, 2012 Product Specification Introduction The AXI Universal Asynchronous Receiver Transmitter (UART) 16550 connects to the AMBA? (Advance Microcontroller Bus Architecture) AXI (Advanced eXtensible Interface) and provides the controller interface for ...
AXI UART 16550 v2.0 .xilinx 4 PG143 November 18, 2015 Product Specification Introduction The LogiCORE™ IP AXI Universal Asynchronous Receiver Transmitter (UART) 16550 connects to the Advance Microcontroller Bus Architecture (AMBA®) AXI and provides the controller interface for asynchronous seri...
DS748 July 25, 2 Product Specification LogiCORE IP AXI UART 16550 (v1.01a) Functional Description The AXI UART 16550 implements the hardware and software functionality of the National Semiconductor 16550 UART, which works in both the 16450 and 16550 UART modes. For complete details, see the ...
引用AXI GPIO的IP,配置为: 然后配置按键的GPIO,根据说明书可知: 对应的原理图如下: 因此设定硬件如下,增加3个EMIO,如下: 引用AXI GPIO的IP,配置为: EMIO的原理图如下: UART 16550 IP配置 每个UART 16550均需要增加两个EMIO,因此这里找4个扩展IO,根据原理可得: 这里选择UART 16550 Rx0,Tx0分别为...
引用AXI GPIO的IP,配置为: 然后配置按键的GPIO,根据说明书可知: 对应的原理图如下: 因此设定硬件如下,增加3个EMIO,如下: 引用AXI GPIO的IP,配置为: EMIO的原理图如下: UART 16550 IP配置 每个UART 16550均需要增加两个EMIO,因此这里找4个扩展IO,根据原理可得: ...
另一个一个最重要的就是编写设备树文件,主要包括LED以及按键的设备树和axi_uart16550设备树文件的编写,内容如下: /include/ "system-conf.dtsi" / { aliases{ ethernet0= &gem0; serial0= &uart1; }; gpio-keys{ compatible = "gpio-keys";
引用AXI GPIO的IP,配置为: 然后配置按键的GPIO,根据说明书可知: 对应的原理图如下: 因此设定硬件如下,增加3个EMIO,如下: 引用AXI GPIO的IP,配置为: EMIO的原理图如下: UART 16550 IP配置 每个UART 16550均需要增加两个EMIO,因此这里找4个扩展IO,根据原理可得: ...
这里用到了zynq、Axi BRAM Controller和一个Block RAM.为了在板上验证,右边添加了一个从PortB读并显示在LED灯上的小模块bram_led。 bram_led的代码比较粗糙,具体的分频数可根据fclk_clk2的配置自行确定。这里设置的50M,因此led灯每1s会随读取到的bram内...
* uartlite Configurable only in HW design * ps7_uart 115200 (configured by bootrom/bsp) */ #include #include #include "platform.h" // DMA无法通过AXI Interconnect访问Microblaze本身的BRAM内存 // 只能访问挂接在AXI Interconnect上的内存