测试连接结果为- [开始:德州仪器 XDS100v2 USB Debug Probe_0] 执行以下命令: %CCS_base%/common/uscif/dbgjtag -f %boarddatafil文件%-RV -o -F inform、logfile=yes -S pathlength -S integrity [结果] --- [打印电路板配置路径名]--- /home/evgenyv/.ti/ti/...
各位老师好,最近开始学习使用28335DSP,但是使用100v2仿真器出现问题,当debug as以后会报 XDS2XX USB DEBUG PROBE 0/C28XX:Error initializing emulator: (Error -2083 @ 0x0) Unable to communicate with the debug probe. Confirm debug probe configuration and connections, reset the debug probe, and retry t...
I'm trying to use my XDS100v2 USB Debug Probe to program and debug a custom board using the AM3351 processor. I was able to define a Target Configuration and successfully pass the 'Test Connection' in the past using Code Composer 6.1.2, but after upgrading to 6.2.0 it fails every tim...
The JTAG DR Integrity scan-test has failed. [End: Texas Instruments XDS100v2 USB Debug Probe_0] === I try to test onboard debug probe with oscilloscope and found that BDBUS0 pin on the U6 (FT2232H) always connected to Vcc (3.3v). Because any other line connected to this pin, I ...
TMDSEMU100V2U-ARM-TEXAS INSTRUMENTS-JTAG Emulator, 20/10Pin, XDS100, USB Bus Powered, No Power Supply Required. 现在就预定 TMDSEMU100V2U-ARM! 质优价廉, 发货迅速的 TEXAS INSTRUMENTS 现货产品。
*** Debug Session Name: Texas Instruments XDS100v1 USB Emulator_0/C28xx*** Board Name: Texas Instruments XDS100v1 USB Emulator_0*** CPU Name: C28xx*** Connecting to target...SEVERE: C28xx: Error connecting to the target: (Error -1135 @ 0x0) The debug probe reported an error. ...
Name:TexasInstrumentsXDS100v3USBDebugProbe_0/C28xx*** Board Name:TexasInstrumentsXDS100v3USBDebugProbe_0*** CPU Name:C28xx*** Connectingtotarget… ***Loadingtheprogramtothe TMS320F28335 debug 报错 “ADC Calibration not complete” 用的CCS8.1.0debug过程中报错如下:C28xx: GEL Output: ADC Calibrat...
"仿真器插上之后有感叹号，CCS测试连接报 [Start: Texas Instruments XDS100v2 USB Debug Probe_0]Execute the command:%ccs_base%/common/uscif/dbgjtag -f %boarddatafile% -rv -o -F inform,logfile=yes -S pathlength -S integrity [Result]"Eric：你删除驱动后重新安装一下试试。还有就是...
新手请教一个小问题,我采用TMDSSK3358的集成的XDS100v2的测试starterware中的程序,我目前使用的是rasterdisplay,程序能运行,我想问的是我在debug 过程中,发现直接进入到main()中,如下: Texas Instruments XDS100v2 USB Debug Probe_0/CortxA8 (Suspended - SW Breakpoint) ...
I have another update. I switched USB cables and I can detect the XDS100 device using xds100serial.exe but I cannot run the debugger. Here's the output from 'Test Connection' [Start: Texas Instruments XDS100v2 USB Debug Probe_0]