-i : interface 网络接口名称 wlan0-c : ilename -c是读取配置文件/etc/wpa_supplicant.conf-B： 后台运行wpa_supplicant.conf是配置文件内容，如果用wpa_cli配置网络的话，至少要保证以下两行在配置文件里# 指定socket路径方便和hostapd_cli通信ctrl_interface=/var/run/wpa_supplicant# 使用wpa_supplicant来扫描...
wpa_cli -i wlan0 -p /var/run/wpa_supplicant reconfigure wpa_cli -i wlan0 -p /var/run/wpa_supplicant reconnect 扫描周边 AP: wpa_cli -i wlan0 -p /var/run/wpa_supplicant scan wpa_cli -i wlan0 -p /var/run/wpa_supplicant scan_results 查看连接情况: wpa_cli -i wlan0 -p /var/ru...
OpnSense as WiFi-Client should reconnect at best effort and not fall into a (nearly) unrecoverable state. Log from wpa_supplicant Starting wpa_supplicant non-daemonized with debug:wpa_supplicant -i ath0_wlan1 -c /var/etc/wpa_supplicant_ath0_wlan1.conf -ddshows(log starts at point where ...
# wpa_cli reconfigure //wpa_supplicant进程起来的时候再次重新加载配置文件/etc/wpa_supplicant.conf# wpa_cli save_config //保存已连过的状态及优先级 # wpa_cli reconnect // 重新连接 一接入USB无线网卡,就自动执行wpa_supplicant等 可以用热插拔mdev机制 一连接WIFI AP,就自动执行dhclient,可以写脚本后台监...
是否可以表明wpa_supplicant问题已得到纠正,并且可以尝试重新进行身份验证?(没有enable_network,reassociate或reconnect工作。) (重新启动wpa_supplicant有效,但我想知道是否有“更温和”的方法。从日志来看,它看起来像是退了,上限高达 20 分钟,这是重试之间的很长时间。) ...
Some scans are * used for changing modes inside wpa_supplicant (roaming, * auto-reconnect, etc). Discarding the scan might hurt these processes. * The normal use case for PNO is to suspend the host immediately after * starting PNO, so the periodic 100 ms attempts to run the scan do ...
以上常常用到的差不多是disconnect, reconnect, scan, scan_results, select_network, list_networks, status, reconfigure 測試WPS wpa_supplicant.conf ##Arm-linux/linux:建立socket ctrl_interface=/var/run/wpa_supplicant ctrl_interface_group=0update_config=1 #ap_scan=1 eapol_version=1 fast_reauth=1 ...
AndroidWiFi扫描流程分析（wpa_supplicant）void wpa_supplicant_req_scan(struct wpa_supplicant *wpa_s, int sec, int usec){ int res;if (wpa_s->p2p_mgmt) { wpa_dbg(wpa_s, MSG_DEBUG,"Ignore scan request (%d.%06d sec) on p2p_mgmt interface",sec, usec);return;} res = eloop_deplete_time...
这主要是考虑到wpa_supplicant是可以同时支持多个网络接口的。 wpa_params数据结构主要记录与网络接口无关的一些参数设置。 而每一个网络接口就用一个wpa_interface数据结构来记录。 在启动命令行中,可以用-N来指定将要描述一个新的网络接口,对于一个新的网络接口,可以用下面六个参数描述: ...
RECONNECT Connect if disconnected (i.e., likeREASSOCIATE, but only connect if in disconnected state). PREAUTH <BSSID> Start pre-authentication with the given BSSID. ATTACH Attach the connection as a monitor for unsolicited events. This can be done withwpa_ctrl_attach(). DETACH Detach the conn...