1 在ASSOCIATING阶段由于丢包导致ASSOC REJECT 03-16 09:22:12.440 D/WifiMonitor( 924): Event [IFNAME=wlan0 CTRL-EVENT-DISCONNECTED bssid=08:cc:68:9e:ac:20 reason=3 locally_generated=1]03-16 09:22:16.596 I/wpa_supplicant(23065): wlan0: CTRL-EVENT-ASSOC-REJECT bssid=0e:bd...
<3>CTRL-EVENT-ASSOC-REJECT status_code=1<3>CTRL-EVENT-STATE-CHANGEid=1state=0BSSID=00:00:00:00:00:00SSID=AirFly<3>CTRL-EVENT-ASSOC-REJECT status_code=1<3>CTRL-EVENT-STATE-CHANGEid=-1state=3BSSID=00:00:00:00:00:00SSID= <3>CTRL-EVENT-SCAN-RESULTS<3>WPS-AP-AVAILABLE<3>Trying to...
5:在ASSOCIATING阶段由于丢包导致ASSOC REJECT Event [IFNAME=wlan0 CTRL-EVENT-DISCONNECTED bssid=08:cc:68:9e:ac:20 reason=3 locally_generated=1] I/wpa_supplicant(23065): wlan0: CTRL-EVENT-ASSOC-REJECT bssid=0e:bd:51:c7:b6:33 status_code=1 解决方法 6.在4WAY_HANDSHAKE阶段由于密码错误、丢...
如果使用了5G Hz无线AP,一定要在配置中添加country=CN或者对应国家Code,否则会导致wpa_supplicant运行时错误连接bssid=00:00:00:00:00:00的AP,日志显示类似: Nov 05 16:18:51 pi-worker2 wpa_supplicant[1932]: wlan0: CTRL-EVENT-ASSOC-REJECTbssid=00:00:00:00:00:00 status_code=16 Nov 05 16:10:2...
CTRL-EVENT-ASSOC-REJECT bssid=xx:xx:xx:xx:xx status_code=x 描述:关联请求被拒绝,其中 bssid 是接入点的 MAC 地址,status_code 是拒绝的原因代码(如 1 表示未指定原因)。 建议:根据 status_code 查找具体原因(可能需要参考 IEEE 802.11 标准),检查信号强度、网络拥塞、接入点配置等问题。 CTRL-EVENT-DIS...
Ok, if you think this issue (CTRL-EVENT-ASSOC-REJECT status_code=16) is not related to the patch we applied I can create separate ticket. But can you please clarify - do you suggest that we should do "wl roam_off 1" each time disconnect event happens, and "wl roam_o...
(12) received 04-20 16:07:59.571 1958 1958 I wpa_supplicant: wlan0: CTRL-EVENT-ASSOC-REJECT bssid...'@0x760802e300): num_active_works --> 0 04-20 16:07:59.571 1958 1958 D wpa_supplicant: Added BSSID...00:1d:7e:59:71:0c into blacklist 04-20 16:07:59.571 1958 1958 D wpa...
#define WPA_EVENT_ASSOC_REJECT "CTRL-EVENT-ASSOC-REJECT " /** wpa_supplicant is exiting */ #define WPA_EVENT_TERMINATING "CTRL-EVENT-TERMINATING " /** Password change was completed successfully */ #define WPA_EVENT_PASSWORD_CHANGED "CTRL-EVENT-PASSWORD-CHANGED " ...
<3>CTRL-EVENT-STATE-CHANGE id=-1 state=0 BSSID=00:00:00:00:00:00 SSID= 现在我们还没有连接⽹络，⾸先使⽤scan命令扫描⼀下附近的wifi⽹络，然后使⽤scan_results显⽰扫描的结果 > scan OK <3>CTRL-EVENT-STATE-CHANGE id=-1 state=3 BSSID=00:00:00:00:00:00 SSID= <3>CTRL-...
描述 Connman是管理嵌入式设备联网的守护进程,集成了大量的通信功能. Connman是一个完全模块化的系统,可以...