-i : interface 网络接口名称 wlan0-c : ilename -c是读取配置文件/etc/wpa_supplicant.conf-B： 后台运行wpa_supplicant.conf是配置文件内容，如果用wpa_cli配置网络的话，至少要保证以下两行在配置文件里# 指定socket路径方便和hostapd_cli通信ctrl_interface=/var/run/wpa_supplicant# 使用wpa_supplicant来扫描...
signal_monitor = set signal monitor parameters pktcnt_poll = get TX/RX packet counters reauthenticate = trigger IEEE 802.1X/EAPOL reauthentication autoscan [params] = Set or unset (if none) autoscan parameters raw <params..> = Sent unprocessed command flush = flush wpa_supplicant state...
.deinit_ap=wpa_driver_nl80211_deinit_ap, .deinit_p2p_cli=wpa_driver_nl80211_deinit_p2p_cli, .resume=wpa_driver_nl80211_resume, .send_ft_action=nl80211_send_ft_action, .signal_monitor=nl80211_signal_monitor, .signal_poll=nl80211_signal_poll, .send_frame=nl80211_send_frame, .shared_freq...
.deinit_p2p_cli = wpa_driver_nl80211_deinit_p2p_cli, .resume = wpa_driver_nl80211_resume, .signal_monitor = nl80211_signal_monitor, ...}structwpa_supplicant *wpa_supplicant_add_iface(structwpa_global *global,structwpa_interface *iface,structwpa_supplicant *parent) {structwpa_supplicant *wpa...
# 指定socket路径方便和hostapd_cli通信 ctrl_interface=/var/run/wpa_supplicant # 使用wpa_supplicant来扫描和选择AP ap_scan=1 # 存储已连接的SSID密码(非必须写入,但一般也要写入),不然使用不了wpa_cli save_config update_config=1 连接不加密的SSID的配置文件 ...
通过adb命令行或hdc命令行,可以直接打开supplicant,从而运行wpa_cli,可以解决没有显示屏而无法操作WIFI的问题,还可以避免UI的问题带到driver。 一、wpa_supplicant 首先打开wpa_supplicant,运行起后才可以使用wpa_cli来连接 #wpa_supplicant -h [WpaSample]init enter. ...
.deinit_p2p_cli=wpa_driver_nl80211_deinit_p2p_cli, .resume=wpa_driver_nl80211_resume, .send_ft_action=nl80211_send_ft_action, .signal_monitor=nl80211_signal_monitor, .signal_poll=nl80211_signal_poll, .send_frame=nl80211_send_frame, ...
1.5 添加firmware 此时开发板启动Linux后,使用ifconfig wlan0 up启动无线网卡,提示: ieee80211 phy0: rt2x00lib_request_firmware...wpa_supplicant是一个连接、配置WIFI的工具,它主要包含wpa_supplicant(命令行模式)与wpa_cli(交互模式)两个程序。...从这里可以看出,最后WIFI名字和密码,都会被保存到一个配置文件...
/bin/sh IFNAME=$1 CMD=$2 if [ "$CMD" = "CONNECTED" ]; then SSID=`wpa_cli -i$IFNAME status | grep ^ssid= | cut -f2- -d=` # configure network, signal DHCP client, etc. fi if [ "$CMD" = "DISCONNECTED" ]; then # remove network configuration, if needed SSID= fi ...
1. 概述 wpa_supplicant是wifi客户端（client）加密认证⼯具，和iwconfig不同，wpa_supplicant⽀持wep、wpa、wpa2等完整的加密认证，⽽iwconfig只能⽀持wep。和wpa_supplocant相对应的，ap端的加密认证⼯具为hostapd。wpa_supplicant运⾏于后台，它需要借助控制台⼯具wpa_cli来进⾏⼿动操作。2. wpa...