Cisco Catalyst 9800 Series Wireless Controller Software Configuration Guide, Cisco IOS XE Cupertino 17.9.x - High Availability [Cisco Catalyst 9800 Series Wireless Controllers] - Cisco https://www.cisco.com/c/dam/en/us/td/docs/wireless/controller/9800/17-6/deployment-guide/c9800-ha-sso-deployment...
从Cisco IOS XE Bengaluru 17.6.1,Cisco Catalyst 9800系列无线控制器支持以太网服务端口(管理接口VRF/GigabitEthernet 0)。 在此版本之前,Catalyst 9800 WLC只能通过SNMP通过其无线管理接口或冗余管理接口进行监控(在版本17.5.1及更高版本的HA集群中的备用WLC的情况下)。 通过Web界面 SNMPv2c是基...
如果配置保留为默认值,并且机箱MAC地址用于形成移动隧道,则发生故障转移时,主用机箱和移动隧道将失败。 因此,强制为C9800 HA对配置移动MAC地址。 第1步:在GUI上,导航至Configuration > Wireless > Mobility > Global Configuration. 通过CLI: # config t # wireless mobility mac-address <AAAA.BBBB...
I have tested old version vWLC 9800 17.X code with HA - as i was reading document : It is important to put C9800 interface that we intend to use as a Redundancy Port L2 HA inter-vWLC 9800 link into a separate, unused VLAN [I cab confirm we have done this, separate interface on ...
- Use one NAD with the WMI address only (HA-standby controller is always inactive) I would simply create the other 2 NADs anyway and check if they are used or not afterwards in the ISE logs. >...Is it possible to have two objects (NADs) with two
ISSU Upgrade Process and Compatibility Version Verification on C9800 WLC 4:54 This video talks about the In-Service Software Upgrade process for the 9800 WLC that are in HA-SSO and how to verify the compatibility of the running and target release. Tags: 9800,WLC,ISSU,upgrade,configuration,comp...
MIB和Cisco WLC上所有对象名称和ID的列表 使用OID监控WLC的状态 通过Snmpwalk监控 通过Python3和Pysnmp库进行监控 与第三方软件集成(Grafana+Prometheus/PRTG网络监控器/SolarWinds) 与CUCM集成 最常见受监控OID的表 HA中的监控备用WLC 直接监控备用WLC 通过主用WLC监控备用WLC 简介 本文档介绍如何配置简单网络管理协议...
思科无线9800WLC: 强制切换 要强制在框之间切换,请手动重新启动活动的9800 WLC或运行此命令: # redundancy force-switchover https://www.cisco.com/c/zh_cn/support/docs/wireless/catalyst-9800-series-wireless-controllers/213915-configure-catalyst-9800-wireless-control.html...
网关IP将从配置的静态IP路由中拾取。HA基础结构将选择与RMI网络匹配的静态路由IP。如果配置了多条静态路由,则选择网络范围最广的路由。可以为同一个网络范围配置多个网关。如果同一网络中有多个网关,则选择最宽掩码和最小网关IP。当配置更新为静态路由时,需要重新评估网关IP。
您可以有一个HA SSO(状态切换)对、一个N+1冗余,或同时拥有两者。 HA SSO:WLC之间有一个连续同步的主用和备用控制器。 N+1:有主控制器和辅助控制器,但它们之间没有互连。两个控制器必须运行相同版本,并且必须配置相同才能无缝运行。AP会连接到主控制器,并在主控制器出现故障时回退到辅助控制器...