如果选择“从头开始创建”的选项: 点击“生成密钥对”(Generate keypair)以生成公钥和私钥。 地址(Addresses):此隧道的WireGuard接口地址。例如,在此示例中为 192.168.200.2/32。 监听端口(Listen port):例如,在此示例中为 32767。 DNS 服务器(DNS Server):局域网中的 DNS 服务器。例如,路由器地址。 点击“添加...
2.1设置local name:随意填写 2.2点击GENERATE KEYPAIR,生成公钥与私钥 生成基本服务端基本配置 2.3点击下方“应用” 3 对等节点配置示例 3.1添加节点ADD PEER ADD PEER 3.2设置节点类型为Remote tunneled access PEER配置 3.3点击节点PEER旁边的眼睛👀 查看对等节点配置 3.4查看生成的配置,二维码可以用手机客户端直接扫...
2.1设置local name:随意填写 2.2点击GENERATE KEYPAIR,生成公钥与私钥 生成基本服务端基本配置 2.3点击下方“应用” 3 对等节点配置示例 3.1添加节点ADD PEER ADD PEER 3.2设置节点类型为Remote tunneled access PEER配置 3.3点击节点PEER旁边的眼睛👀 查看对等节点配置 3.4查看生成的配置,二维码可以用手机客户端直接扫...
填写相关信息,这里相当于wg0.conf配置文件里的[Interface]相关条目,也就是设置本机的相关接口信息。点击generate keypair生成密钥对后将自动填好。切换basic到advanced打开全部项目。 以下简要说明必填项目: Network protocol: ipv4 only # 为了简化配置,选择ipv4 only即可,地址方便记忆。 Local tunnel network pool: 10...
Generating Server and Client Key Pair In this step, you'll generate key pair for the wireguard server and client. And this can be done via the 'wg' command utility that is provided by the wireguard-tools package. Below are two utilities that are provided by wireguard-tools: ...
Click Generate a Key Pair. Enter WireGuard Interface IP.(We can use Vigor Router’s LAN IP as the WireGuard Interface IP) Click OK to save.2. Go to VPN and Remote Access >> Remote Dial-in User to create a profile.Check Enable this account. Check WireGuard as Dial-In Type. Enter ...
Click Generate a Key Pair. Enter WireGuard Interface IP.(We can use Vigor Router’s LAN IP as the WireGuard Interface IP) Click OK to save.2. Go to VPN and Remote Access >> Remote Dial-in User to create a profile.Check Enable this account. Check WireGuard as Dial-In Type. Enter ...
# 生成密钥对 root@vyos:/# generate wireguard keypair # 查看密钥对公钥信息,对端需要使用 root@vyos:/# show wireguard pubkey ylKfhiqfpkvPGwgGO5MigmNR0Wv1/nMhq2a3KdU1wRk= root@gw2:/# show configuration commands set interfaces ethernet eth1 address '10.1.8.1/24' set interfaces ethernet eth1...
{{ i18n "pages.xray.wireguard.secretKey" }} </template>
Step 2: Generate Public/Private Keypair Server Run the following command on the Ubuntu server to create a public/private key pair, which will be saved under/etc/wireguard/directory. wg genkey | sudo tee /etc/wireguard/server_private.key | wg pubkey | sudo tee /etc/wireguard/server_public...