Example> route ADD 157.0.0.0 MASK 155.0.0.0 157.55.80.1 IF 1 The route addition failed: The specified mask parameter is invalid. (Destination & Mask) != Destination. Examples: > route PRINT > route ADD 157.0.0.0 MASK 255.0.0.0 157.55.80.1 METRIC 3 IF 2 destination^ ^mask ^gateway metric...
ifIndex DestinationPrefix NextHop RouteMetric--- --- --- ---2 0.0.0.0/0 192.168.1.1 25 3 192.168.1.0/24 192.168.1.1 10 在这个例子中,Metric值为 25 的路由在ifIndex为 2 的接口上,它的度量值较高,因此只有在 Metric 值较低的路由不可用时才会被使用。 3.ifIndex 和 Metric 的区别与对比 4....
发往存储网络的数据包在路由器被转发时,会优先走 RouteMetric 小的那个口。 注意,如图1 所示,网络面板适配器属性里,也可设置 IPv4/IPv6 的跃点数。但是这个跃点数与上面提到的 RouteMetric 是两个值。这里的 Metric 叫做 IfMetric,即网络接口跃点数。一条路由表会同时有这两个 Metric,但是 RouteMetric 的优先...
Example> route ADD 157.0.0.0 MASK 155.0.0.0 157.55.80.1 IF 1 The route addition failed: The specified mask parameter is invalid. (Destination & Mask) != Destination. Examples: > route PRINT > route ADD 157.0.0.0 MASK 255.0.0.0 157.55.80.1 METRIC 3 IF 2 destination^ ^mask ^gateway metric...
route delete删除一条路由 7、永久添加一条路由 route add ipnet mask x.x.x.0 gateway -p添加永久路由 三、使用语法及参数说明 1、使用语法 用法:ROUTE [-f] [-p] [-4|-6] command [destination] [MASK netmask] [gateway] [METRIC metric] [IF interface] ...
IPv4 Route Table === Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.0.1 192.168.1.12 26 10.108.0.0 255.255.0.0 10.108.58.1 10.108.58.18 21 10.108.58.0 255.255.255.0 On-link 10.108.58.18 276 10.108...
ROUTE [-f] [-p] [-4|-6] command [destination] [MASKnetmask] [gateway] [METRIC metric] [IF interface] -f 清除所有网关项的路由表。如果与某个 命令结合使用,在运行该命令前, 应清除路由表。 -p 与 ADD 命令结合使用时,将路由设置为 在系统引导期间保持不变。默认情况下,重新启动系统时, 不保存...
route命令基本格式:ROUTE[-f][-p][-4|-6]command[destination][MASKnetmask][gateway][METRICmetric][IFinterface]子命令: command Oneofthese:PRINTPrints a routeADDAdds a routeDELETEDeletes a routeCHANGEModifies an existing route 此指令在windows 10 命令行中有详细的命令使用说明,大家可以自行阅读; ...
Route> </Routes> </Interface> <Interface wcm:action="add"> <Ipv4Settings> <DhcpEnabled>true</DhcpEnabled> <Metric>20</Metric> <RouterDiscoveryEnabled>false</RouterDiscoveryEnabled> </Ipv4Settings> <Ipv6Settings> <DhcpEnabled>false</DhcpEnabled> <Metric>10</Metri...
After doing some research, I found that if we configure same adapter metric manually for WiFi and Ethernet then we will have two default route with the same metric in the routing table.IPv4 Route TableActive Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 10.38....