启动WireGuard:使用以下命令启动WireGuard服务: sudo wg-quick up wg0 配置防火墙:为了允许流量通过WireGuard接口,您需要配置防火墙以允许相应的端口和数据传输。 在Ubuntu或Debian上配置防火墙: sudo ufw allow <服务器监听端口>/udp sudo ufw enable 将<服务器监听端口>替换为您在配置文件中设置的服务器监听端口。 在...
按照上面的方式离线安装wg后,使用systemctl status wg-quick@wg0查看运行失败。使用wg-quick up wg0启动wg报: #sudo wg-quick up wg0[#] ip link add wg0 type wireguardUnable to access interface: Protocol not supported[#]ip link delete dev wg0Cannot find device "wg0" 通过错误信息搜索问题大多是...
另一端直接reverse过来,注意最好用两对密钥 3. windows端安装tunsafe,并且安装合适TAP驱动,注意和openvpn的tap可能冲突。另外注意官方的windows程序利用TUN有些bug不好用。连接上去测试 ping linux端通过,(反向ping windows需要打开Windows防火墙! 所以建议还是用nc开一个tcp的端口互相发送测试) 4. 设置转发, sysctl n...
*wg-quick: darwin: account for "link#XX" gatewaysLaura Hausmann2021-08-121-2/+2 *ipc: windows: use devpkey instead of nci for nameJason A. Donenfeld2021-07-314-120/+41 *ipc: windows: don't display disabled adaptersJason A. Donenfeld2021-07-201-1/+4 ...
*wg-quick: linux: check for CAP_NET_ADMIN and config file access before auto_sujd/capability-checkJason A. Donenfeld2020-08-281-1/+20 *version: bumpv1.0.20200827Jason A. Donenfeld2020-08-271-1/+1 *Revert "wg-quick: wait on process substitutions"Jason A. Donenfeld2020-08-274-49/+49...
To get started with WireGuard, you can follow the Quick Start guide on the WireGuard website, which provides step-by-step instructions for setting up a basic WireGuard configuration on Linux. If you encounter the below error while running the command wg: ...
8. 开始关闭linux端的wg用 wg-quick up/down wgxxx status 用wg show来看 (update1: 更新两个很有用的命令,用来开启pve虚拟机里面的vm的serial串口,从而xterm systemctl enable serial-getty@ttyS0.service systemctl start serial-getty@ttyS0.service ...
wg-quick down wg0 yum remove -y wireguard-dkms wireguard-tools rm -rf /etc/wireguard/ echo "卸载完成" } config_client(){ cat > /etc/wireguard/client.conf <<-EOF [Interface] PrivateKey = $c1 Address = 10.0.0.2/24 DNS = 114.114.114.114 ...
2、终止wgcf:systemctl stop wg-quick@wgcf 二、多平台优选WARP对端IP + 无限生成WARP-Wireguard配置 一键脚本,建议苹果手机与安卓手机在本地网络使用 curl -sSL https://gitlab.com/rwkgyg/CFwarp/raw/main/point/endip.sh -o endip.sh && chmod +x endip.sh && bash endip.sh ...
Rekeying offers a quick, cost-effective way to change access when needed, while replacing locks provides the opportunity to improve security and functionality, particularly when locks are old or worn. By rekeying locks every few years and replacing them approximately every decade, you can ensure ...