wg-quick down wg0 这将停止并移除wg0接口及其所有配置。 如果wg0接口未在使用中或已成功停止/移除,重新配置并启动新的wg0接口: 确保你有正确的配置文件(通常是/etc/wireguard/wg0.conf),然后使用以下命令来启动新的wg0接口: bash wg-quick up wg0 验证新的wg0接口是否成功启动并可以正常使用: 再次使用...
启动WireGuard:使用以下命令启动WireGuard服务: sudo wg-quick up wg0 配置防火墙:为了允许流量通过WireGuard接口,您需要配置防火墙以允许相应的端口和数据传输。 在Ubuntu或Debian上配置防火墙: sudo ufw allow <服务器监听端口>/udp sudo ufw enable 将<服务器监听端口>替换为您在配置文件中设置的服务器监听端口。 在...
sudo wg-quick up ~/wg0.conf #如果提示wg0存在时(wg-quick: `wg0' already exists)执行下面一行 #sudo ip link delete dev wg0 网卡相关的一些命令 sudo ip link add wg0 type wireguard sudo ip link delete dev wg0 sudo ip link set up dev wg0 sudo ifconfig wg0 up ifconfig 3.添加更多的...
按照上面的方式离线安装wg后,使用systemctl status wg-quick@wg0查看运行失败。使用wg-quick up wg0启动wg报: #sudo wg-quick up wg0 [#] ip link add wg0 type wireguard Unable to access interface:Protocol not supported [#]ip link delete dev wg0 Cannot find device "wg0" 通过错误信息搜索问题大...
# wg-quick up /path/to/wgnet0.conf For convenience, if only an interface name is supplied, it automatically chooses a path in `/etc/wireguard/': # wg-quick up wgnet0 This will load the configuration file `/etc/wireguard/wgnet0.conf'. The strip command is useful for reloading configu...
配置文件写好后,使用 wg-quick 工具来创建虚拟网卡, AI检测代码解析 wg-quick up wg0 1. 上面命令中的 wg0 对应的是 /etc/wireguard/wg0.conf 这个配置文件,其自动创建的网卡设备,名字就是 wg0,这对应关系自不必多言。
当我通过wg-quick up wg0添加一个wireguard接口时,wg-快速设置以下nftable规则。这些都在做什么,为什么需要它们? 下面是ipv4的一些示例规则: 代码语言:javascript 运行 AI代码解释 table ip wg-quick-wg0 { chain preraw { type filter hook prerouting priority raw; policy accept; iifname != "wg0" ip d...
## 问题原因 我可以理解,开发人员不想使用苹果使用的旧bash v3。但从用户的帖子来看,安装一个较新的bash并不那么好 所以我看了wireguard的wg-quick。需要支持的唯一变化,两个bash版本都是为了摆脱关联数组SERVICE_DNS,并处理v3的BASHPID。 ## 解决方案
# wg-quick up /path/to/wgnet0.conf For convenience, if only an interface name is supplied, it automatically chooses a path in `/etc/wireguard/': # wg-quick up wgnet0 This will load the configuration file `/etc/wireguard/wgnet0.conf'. ...
check with ip a or wg show or wg-quick up wg0 that the tunnel is up - as expected then wait for the Zincati auto-update or enforce it to happen now - after update and reboot the tunnel is down and cannot be (re)started. check journalctl or try manually to start the tunnel - an...