[R1-GigabitEthernet0/0/0.10]ip address 192.168.10.253 24 [R1-GigabitEthernet0/0/0.10]vrrp vrid 10 virtual-ip 192.168.10.254 [R1-GigabitEthernet0/0/0.10]vrrp vrid 10 priority 120 [R1-GigabitEthernet0/0/0.10]vrrp vrid 10 track interface Gi0/0/1 reduced 30 [R1-GigabitEthernet...
vrrpvrid10 priority 120 备交换机配置例::interfaceVlan-interface 10 ipaddress 192.168.1.253 255.255.255.0 vrrpvrid10 virtual-ip192.168.1.254 vrrpvrid10 priority 100 其中virtual-ip192.168.1.254就是192.168.1.0(VLAN10)内主机的网关。 三层交换机C配置如下(我这是千M电口和百M混用,你们可以实际情况来定)...
设置VRRP(虚拟路由冗余协议)的优选级值为120，值越大越优先
vrrp vrid 14 virtual-ip 192.168.4.100 vrrp vrid 14 priority 120 vrrp vrid 14 preempt-mode timer delay 20 interface Vlanif 15 vrrp vrid 15 virtual-ip 192.168.5.100 vrrp vrid 15 priority 120 vrrp vrid 15 preempt-mode timer delay 20 interface Vlanif 16 vrrp vrid 16 virtual-ip 192.168....
port trunk allow-pass vlan 10 20 return 六、switchA交换机的主要配置文件：# sysname SwitchA # vlan batch 10 20 30 # stp disable # interface Vlanif10 ip address 192.168.10.1 255.255.255.0 vrrp vrid 1 virtual-ip 192.168.10.254 vrrp vrid 1 priority 120 vrrp vrid 1 preempt-mode ...
命令: vrrp vrid 10 priority 110#默认优先级为100,优先级越大越优先,在接口下优先级修改为110 将修改ar1的优先级后使用display vrrp命令分别查看两台路由器的vrrp详细信息 发现ar1成为了master,ar2成为了backup,虚拟IP为192.168.1.5,master IP为ar1的接口地址 ...
VRRP 10 virtual-ip:192.168.10.254 vlanif20:192.168.20.252/24 VRRP 20 virtual-ip:192.168.20.254 Router:GE0/0/0:192.168.201.2/24,GE0/0/1:192.168.202.2/24,GE0/0/2:192.168.1.254/24 三、配置步骤: 1.所有设备完成基础配置 SW3的配置如下: ...
[LSW1-Vlanif10][LSW1-Vlanif10]vrrp vrid 1 virtual-ip 192.168.1.254 //配置VLAN10 的虚拟网关地址 [LSW1-Vlanif10]vrrp vrid 1 priority 120 //配置VRRP优先级,默认100,越高越优先 [LSW1-Vlanif10]vrrp vrid 1 track interface g0/0/1 reduced 60 //配置链路跟踪,当检测 g0/0/1接口故障时优...
其中SW1为VRRP组10及20的Master,为组30及40的Backup: [SW1] interface Vlanif 10 [SW1-vlanif10] ip address 192.168.10.253 255.255.255.0 [SW1-vlanif10] vrrp vrid 10 virtual-ip 192.168.10.254 [SW1-vlanif10] vrrp vrid 10 priority 120...
vrrp vrid 1 priority 120 //vrrp1的优先级为120 vrrp vrid 1 preempt-mode timer delay 20 //vrrp1的抢占时间为20秒 vrrp vrid 1 track interface gigabitethernet1/0/1 reduced 100 //监视上行接口,一旦断开就降优先级,让核心2顶上 vrrp vrid 1 track interface eth-trunk 13 reduced 100 //监视下行...