Thanks this is very helpful so far, but I have some questions please;- Do not use a Layer 2 vPC to attach L3 device to a vPC domain unless L3 device can statically route to the HSRP address configured on vPC peer device. This statement means that definitely I won't be able to use ...
n7k(config-vpc-domain)# peer-keepalive destination 172.28.1.100 source 172.28.1.120 vrf default 4、配置系统优先级 n7k(config-vpc-domain)# system-priority 4000 5、配置角色优先级 n7k(config-vpc-domain)# role priority 2000 6、当在配置了VPC的设备上启用三层转发时(启用SVI接口)必需配置peer-gateway(P...
Leaf1# vpc domain 1//配置vPC域role priority 10 peer-keepalive destination 10.10.1.2 source 10.10.1.1 auto-recovery interface port-channel1//配置Peer-linkswitchport switchport mode trunk switchport trunk allowed vlan 100 spanning-tree port type network vpc peer-link interface port-channel10//配置互...
N9K-2(config)#spanning-tree vlan 1,10,20 priority 0N9K-2(config)#endN9K-2#show running-config spanning-treespanning-tree vlan 1,10,20 priority 0 interface port-channel1 spanning-tree port type network N9K-1#show running-config spanning-treespanning-tree vlan 1,10,20 priority 0 interface ...
N7K1# show run vpc version 6.1(2)feature vpc vpc domain 10 role priority 100 peer-keepalive destination 10.201.254.254 source 10.201.254.253 vrf VPC peer-gateway auto-recovery interface port-channel1 vpc peer-link interface port-channel20 vpc 20 interface port-channel30 vpc 30 N7K2# show run...
vpc domain 10 peer-switch peer-gateway role priority 100 system-priority 200 peer-keepalive destination 192.168.11.2 source 192.168.11.1 # interface Eth-Trunk0 peer-link description Peer-link mode lacp-static peer-link 1 # interface Eth-Trunk1 M-LAG description M-LAG port mode lacp-static ...
vPC Role and Priority sw1(config)# vpc domain <domain-id> sw1(config-vpc-domain)# role priority 100 sw2(config)# vpc domain <domain-id - 同sw1> sw2(config-vpc-domain)# role priority 110 vPC role是非抢占性的,但是STP是抢占性的,可能会出现STP ROOT和vPC operational primary设备不一致的情...
n9k-1(config)# vpc domain 1 1. 配置vpc角色优先级 n9k-1(config-vpc-domain)# role priority 100 Warning: !!:: vPCs will be flapped on current primary vPC switch while attempting role change ::!! Note: ---:: Change will take effect after user has re-initd the vPC peer-link ::-...
vPC role : primaryDual Active Detection Status : 0vPC system-mac : 00:23:04:ee:be:65vPC system-priority : 32667vPC local system-mac : c0:14:fe:b0:d6:13vPC local role-priority : 100vPC local config role-priority : 100vPC peer system-mac : c0:14:fe:b0:be:8fvPC peer role-...
N5k-1(config)# vpc domain 1 Step5. 配置vPC role priority (可选). N5k-1(config-vpc-domain)# role priority 1000 Step6. 配置peer keepalive link. N5K SW2的管理接口IP地址是172.25.182.52. N5k-1(config-vpc-domain)# peer-keepalivedestination 172.25.182.52 ...